Window Wiper and Wiper Motor (Front) - Remove and Install
Start By:
- Remove steering wheel.
- Remove bolts (3) and plate (2). Relocate floor mat (1).
Show/hide table
Illustration 2 g03805502 Show/hide table
Illustration 3 g03805511 - Remove cover (4). Disconnect harness assemblies (5). Remove cover (6).
Show/hide table
Illustration 4 g03805494 - Remove cover (7). Separate lower panel (8) at Location (X). Remove lower panel (8).
Show/hide table
Illustration 5 g03805517 Show/hide table
Illustration 6 g03805580 Show/hide table
Illustration 7 g03805587 - Remove bolts (9). Remove mat (10). Remove bolt (11).
Show/hide table
Illustration 8 g03805595 - Lean cover assembly (12) rearward toward the steering column.
Show/hide table
Illustration 9 g03805600 - Disconnect cable assembly (13) from the latch. Remove nut (14), feed the cable assembly (13) out of the bracket.
Show/hide table
Illustration 10 g03805610 Show/hide table
Illustration 11 g03805636 - Raise caps (15) and remove nuts (16). Remove nuts (17).
Show/hide table
Illustration 12 g03805642 - Disconnect harness assembly (18). Remove front wiper motor (19).
Show/hide table
| |
| Illustration 1 | g01119509 |
- Install front wiper motor (19) in the reverse order of removal.
- Tighten nuts (17) to a torque of
15 N·m (133 lb in) . - Tighten wiper arm nut (16A) to a torque of
24 N·m (212 lb in) , allow to relax for 30 minutes. Retorque to a torque if24 N·m (212 lb in) . - Tighten wiper arm nut (16B) to a torque of
40 ± 5 N·m (30 ± 4 lb ft) , allow to relax for 30 minutes. Retorque to a torque of40 ± 5 N·m (30 ± 4 lb ft) .
Show/hide table
Illustration 13 g03805694 Show/hide table
Illustration 14 g03805675 - Tighten nuts (17) to a torque of
Caterpillar Information System:
14M3 Motor Grader Electrical System Troubleshooting HVAC, Condensate Drainage System
16M Series 3 and 18M Series 3 Motor Graders HVAC, Air Conditioning System
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Water Spray System Filter - Clean
RM500B Reclaimer Mixer Machine Systems Rotor Transmission (Input Shaft, Rotor Transmission Case, and Transmission Planetary) - Remove and Install
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Water Spray System - Drain
16M Series 3 and 18M Series 3 Motor Graders HVAC, Visual Inspection
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Water Spray Nozzles - Clean
994K Wheel Loader CAN Data Link - Test
794 AC Off-Highway Truck Field Assembly Introduction
239D and 249D Compact Track Loaders and 226D and 232D Skid Steer Loaders Machine Systems Gear Pump - Assemble - High Flow
239D and 249D Compact Track Loaders and 226D and 232D Skid Steer Loaders Machine Systems Gear Pump - Assemble - Standard Flow
239D and 249D Compact Track Loaders and 226D and 232D Skid Steer Loaders Machine Systems Gear Pump - Disassemble - High Flow
CP-533E and CS-533E Vibratory Soil Compactors Maintenance Interval Schedule
CD44B and CD54B Vibratory Asphalt Compactors Maintenance Interval Schedule
C3.4B Engines for Caterpillar Built Machines Introduction
C3.4B Engines for Caterpillar Built Machines Electronic Control System
C3.4B Engines for Caterpillar Built Machines Power Sources
C3.4B Engines for Caterpillar Built Machines Glossary of Electronic Control Terms
C3.4B Engines for Caterpillar Built Machines Engine Valve Lash - Inspect
C3.4B Engines for Caterpillar Built Machines Position the Valve Mechanism Before Maintenance Procedures
Installing Product Link Kits to F2 Series Backhoe Loaders{1408, 7490, 7601, 7603, 7610, 7620} Installing Product Link Kits to F2 Series Backhoe Loaders{1408, 7490, 7601, 7603, 7610, 7620}
CB64B, CB66B and CB68B Vibratory Asphalt Compactors Fuses - Replace
906K, 906M, 907K, 907M, 908K and 908M Compact Wheel Loaders Hoses and Clamps - Replace
Installation of Mechanically Attached Sidebar Protectors on Loader Bucket{6101, 6102, 6817} Installation of Mechanically Attached Sidebar Protectors on Loader Bucket{6101, 6102, 6817}