Alternator Problem - Charging Problem and/or Noisy Operation
- Alternator
- Charging Circuit
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. Condition of the Alternator Drive Belts A. Inspect the condition of the alternator drive belts. B. Check the belt tension. If the engine is equipped with an automatic belt tensioner, check the automatic belt tensioner. Excessive belt tension can result in damage to the alternator. |
Drive Belt |
Result: The alternator drive belts are in good condition and the belt tension is correct. Repair: Proceed to Test Step 2. Result: The alternator drive belts are not in good condition or the belt tension is incorrect. If the alternator drive belts are worn or damaged, replace the belts. Refer to Disassembly and Assembly for the correct procedure. If necessary, replace the automatic belt tensioner. Refer to Disassembly and Assembly for the correct procedure. |
2. Condition of the Alternator Drive Pulley A. Check the condition of the alternator drive pulley. Look for deep grooves that have been worn into the pulley by the belt. Check that the nut for the pulley has not become loose. |
Alternator Drive Pulley |
Result: There is excessive wear on the alternator drive pulley. Repair: Replace the pulley. Result: The alternator drive pulley nut was loose. Tighten the nut. Result: There is not excessive wear on the alternator drive pulley. Proceed to Test Step 3. |
3. Wear of the Alternator Bearings A. Check the alternator bearings for signs of wear. |
Alternator bearings |
Result: The alternator bearings are OK. Proceed to Test Step 4. Result: The alternator bearings are not OK. Repair: Repair the alternator or replace the alternator, as needed. Refer to Disassembly and Assembly for the correct procedure. |
4. Operation of the Alternator or Regulator A. Verify that the alternator or the regulator is operating correctly. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting" for the proper testing procedures. |
Regulator and alternator |
Result: The regulator and alternator are operating properly. Proceed to Test Step 5. Result: The regulator and alternator are not operating properly. Repair: Repair the alternator and regulator or replace the alternator and regulator, as needed. Refer to Disassembly and Assembly for the correct procedure. |
5. Inspection of the Charging Circuit A. Inspect the battery cables, wiring, and connections in the charging circuit. |
Charging circuit |
Result: The charging circuit is not working properly. Repair: Clean all connections and tighten all connections. Replace any faulty parts. |
Caterpillar Information System:
735C and 745C Articulated Trucks Machine Systems Brake Accumulator (Parking)
2015/04/10 Torque Converter Fill and Check Location is Improved on Certain 777G Off-Highway Trucks {3016, 3101, 3105, 7076, 7150, 7153, 7261}
RM500B Reclaimer Mixer Machine Systems Communication Electronic Control Module (Product Link)
RM500B Reclaimer Mixer Machine Systems Water Spray Lines
Field Procedure to Improve the Torque Converter Fill and Check Location on Certain 777G Off-Highway Trucks {3016, 3101, 3105, 7076, 7150, 7153, 7261, 7960} Field Procedure to Improve the Torque Converter Fill and Check Location on Certain 777G Off-Highway Trucks {3016, 3101, 3105, 7076, 7150, 7153, 7261, 7960}
RM500B Reclaimer Mixer Machine Systems Heater and Air Conditioner Lines
793F CMD Off-Highway Truck/Tractor Braking System MID 116 - CID 1608 - FMI 13
RM500B Reclaimer Mixer Machine Systems Air Lines
793F CMD Off-Highway Truck/Tractor Braking System MID 116 - CID 1607 - FMI 13
D7E Track-Type Tractor Systems Pump Control Valve (Steering)
RM500B Reclaimer Mixer Machine Systems Exhaust Lines
D6T Track Type Tractor Machine Systems Expansion Valve (Refrigerant)
735C and 745C Articulated Trucks Machine Systems Electronic Control (Hydraulic System)
C27 and C32 Engines for Caterpillar Built Machines Coolant Contains Oil
C27 and C32 Engines for Caterpillar Built Machines Coolant Contains Fuel
C27 and C32 Engines for Caterpillar Built Machines Cylinder Is Noisy
C27 and C32 Engines for Caterpillar Built Machines Engine Cranks but Does Not Start
735B, 740B and 740B EJECTOR Articulated Trucks Chassis Electronic Control System Interaxle Lock Supply Pressure Is High
735B, 740B and 740B EJECTOR Articulated Trucks Chassis Electronic Control System Interaxle Lock Supply Pressure Is Low
RM500B Reclaimer Mixer Machine Systems Control Valve (Front Auxiliary Manifold)
RM500B Reclaimer Mixer Machine Systems Control Valve (Front Auxiliary Manifold)
RM500B Reclaimer Mixer Machine Systems Lines (Rotor Transmission)
RM500B Reclaimer Mixer Machine Systems Coolant Tank and Lines
RM500B Reclaimer Mixer Machine Systems Diesel Exhaust Fluid Lines