Heater Element - Test
Show/hide table
柴油发动机的排气含有可伤害人体的燃烧产物。 必须要在通风良好的地方起动发动机,如果在密闭的地方起动,就要把排气通到外面。 |
Show/hide table
旋转和运动的部件会造成人身伤害。 应避开所有旋转和运动的部件。 机器移动或发动机运转时决不能试图进行部件的调整工作,除非另有规定。 机器必须停在水平地面上,且发动机停止运转。 维修、修理或调整机器前,在起动开关和控制装置上要贴上"禁止操作"或类似的警告标签。 |
Show/hide table
熨平板可能会掉落。 为避免可能的人身伤害,熨平板升起时要伸出熨平板行驶锁。 |
Show/hide table
技术规格 | ||
元件位置 | 目标测量值 | 实际测量值 |
前缘 | 115.8 至 134.1 欧姆 | |
中位 | 52.1 至 60.3 欧姆 | |
后缘 | 115.8 至 134.1 欧姆 |
主熨平板和各伸缩板的各段均有三个加热元件:一个在鼻板上,一个在主熨平板上,另外一个在熨平板的后缘。
以下步骤描述了右熨平板伸缩板上加热元件的测试程序。
测试其他段的程序与之相同。
Show/hide table
所需工具 | |||
工具 | 数量 | 零件号 | 说明 |
A | 1 | 257-9140 | 数字万用表 |
- 把机器开到平整水平的路面。
Show/hide table
图 1 g03723720 - 将行驶选择开关 (1) 移到空档位置。
- 将行驶速度旋钮 (2) 逆时针转到最小位置。
Show/hide table
图 2 g03723722 - 将停车制动器操纵杆 (3) 移到接通位置。
Show/hide table
图 3 g03728333 - 如有必要,将油门操纵杆 (4) 移到高怠速位置。
Show/hide table
图 4 g03723739 - 将锁 (5) 移到一旁,然后将熨平板提升杆 (6) 移到提升位置。 完全提升熨平板。
Show/hide table
图 5 g03728336 - 将右熨平板伸出开关 (11) 移到伸出位置。 完全伸出右熨平板伸缩板。
Show/hide table
图 6 g03728337 - 将左熨平板伸出开关 (8) 移到伸出位置。 完全伸出左熨平板。
Show/hide table
图 7 g03728338 - 将右熨平板锁 (9) 移到锁止位置。
Show/hide table
图 8 g03728340 - 将左熨平板锁 (10) 移到锁止位置。
Show/hide table
图 9 g03723736 - 将油门操纵杆 (4) 移到低怠速位置。
- 将熨平板提升杆 (6) 移到浮动位置。 允许熨平板放置在熨平板锁上。
Show/hide table
图 10 g03723740 - 将发动机起动开关 (7) 转到断开位置。
- 允许熨平板冷却到环境温度。
Show/hide table
图 11 g03728344 - 拆下两颗螺栓 (13) 和垫圈。 拆下盖板 (12)。
注: 熨平板的各段均配备三对接头 (14)、 (15) 和 (16)。 一对接头用于熨平板后缘上的加热元件。 第二对接头用于熨平板中段的加热元件。 第三对接头用于熨平板前缘上的加热元件。 熨平板各段间的接头位置不连贯。 沿着每对接头的导线确定与各对接头相关的加热元件。
- 找出与熨平板后缘上加热元件相连的导线。 从机器线束组件上断开这些导线。
- 使用工具 (A) 测量熨平板后缘上加热元件的电阻。 电阻应为 115.8–134.1 欧姆。
- 将熨平板后缘上的加热元件重新连接到机器线束上。
- 找出与熨平板中间加热元件相连的导线。 从机器线束组件上断开这些导线。
- 使用工具 (Q) 测量熨平板中间加热元件的电阻。 电阻应为 52.1–60.3 欧姆。
- 将熨平板中间的加热元件重新连接到机器线束组件上。
- 找出与熨平板前缘上加热元件相连的导线。 从机器线束组件上断开这些导线。
- 使用工具 (A) 测量熨平板前缘上加热元件的电阻。 电阻应为 115.8–134.1 欧姆。
- 将熨平板前缘上的加热元件重新连接到机器线束组件上。
- 如果任何电阻测量值都不在规定范围内,更换加热元件。
- 将盖板 (12) 放置到位。 安装两个螺栓 (13) 和垫圈。
Show/hide table
图 12 | g03728345 |
Caterpillar Information System:
785G Off-Highway Truck Systems Temperature Sensor (Steering Oil)
M318F, M320F and M322F Wheeled Excavators Hydraulic System Piston Pump (Fan Drive)
2014/09/22 Improved Retention of Fasteners {5622}
AP255E Asphalt Paver Machine Systems Conveyor Chain (Drag) - Adjust
AP255E Asphalt Paver Machine Systems Conveyor Drive Chain (Drag) - Check and Adjust
785G Off-Highway Truck Capacities (Refill)
785G Off-Highway Truck Systems Transmission Hydraulic Control
M318F, M320F and M322F Wheeled Excavators and MH3022 and MH3024 Material Handlers Sound Information and Vibration Information
C4.4 Engines NOx Sensor - Test
773E Off-Highway Truck Power Train Transmission Control
C4.4 Engines Motorized Valve - Test
M318F, M320F and M322F Wheeled Excavators and MH3022 and MH3024 Material Handlers Backup Controls
M318F, M320F and M322F Wheeled Excavators Hydraulic System Pump Control - Fan
785G Off-Highway Truck Systems Pressure Switch - Manifold Bypass
Procedure to Inspect and Rework the Frame 4 Bar Casting to Main Rail Connection Offset on the 793F Off-Highway Truck {0679, 7051} Procedure to Inspect and Rework the Frame 4 Bar Casting to Main Rail Connection Offset on the 793F Off-Highway Truck {0679, 7051}
2014/09/26 The Brake Control Group has been Improved on the 795F AC Off-Highway Truck {4257, 4265, 4269}
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Steering Control Valve - Assemble
785G Off-Highway Truck Systems Steering Accumulator
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Steering Control Valve - Disassemble
PL83 and PL87 Pipelayers Fuel System Secondary Filters - Replace
2014/09/24 The Bodies have been Improved on Certain 793 Off-Highway Trucks {7250, 7258}
Improved Service Brake Accumulator Lines Routing Is Now Used on Certain 793F Off-Highway Trucks {4265, 4282} Improved Service Brake Accumulator Lines Routing Is Now Used on Certain 793F Off-Highway Trucks {4265, 4282}
PL83 and PL87 Pipelayers Fuel System Secondary Filters - Replace
2014/10/01 Frame Assembly is Improved on the 795F AC and the 795F XQ Off-Highway Trucks {7051, 7200, 7201, 7213}