1. Home
  2. Caterpillar
  3. Operation and Maintenance Manual
  4. #i05662741

994K Wheel Loader Caterpillar


Engine Oil Level - Check

Usage:

994K MM9

  • Open the engine access doors on the right-hand side of the machine.
    Show/hide table
    Illustration 1g03590002
    (1) Engine oil level gauge
    (2) Engine oil filler cap

  • Remove engine oil level gauge (1) and clean the gauge with a clean cloth. Reinsert the gauge completely and remove the gauge again. This procedure will give a more accurate measurement of the oil level.

  • When the engine is running at low idle, check the "ENGINE AT LOW IDLE WITH WARM OIL" side of the engine oil level gauge. Maintain the oil level between the "ADD" mark and the "FULL" mark.

    When the engine is stopped, check the "ENGINE STOPPED WITH OIL COLD" side of the engine oil level gauge. Maintain the oil level between the "ADD" mark and the "FULL" mark.

  • If necessary, remove engine oil filler cap (2) and add oil.

  • Make sure that the engine oil level gauge and the filler cap are installed securely.

  • Close the right-hand engine access doors.

    • Caterpillar Information System:

    14L Motor Grader System Pressure - Release
    Cat® Terrain for Drilling Onboard USB Tool
    2014/04/29 An Improved Radiator Cowling Group Is Now Used on 777G Off-Highway Trucks {7155, 7170, 7267}
    416F2, 420F2 and 430F2 Backhoe Loaders Safety Messages
    Product Link 121S/300 MID 122 - CID 0168 - FMI 00
    Product Link 121S/300 Diagnostic Code List
    422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Transmission Oil Filter - Replace
    Product Link 121S/300 Event Code List
    Procedure to Properly Connect and Disconnect the High-Voltage Connectors on "F" Series Asphalt Pavers {1408} Procedure to Properly Connect and Disconnect the High-Voltage Connectors on "F" Series Asphalt Pavers {1408}
    422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Transmission Oil - Change
    Product Link 121S/300 Operating Hours Discrepancy
    Product Link 121S/300 Diagnostics and Events Not Available
    980M and 982M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems General Information (Brake System)
    794 AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) Cable Connections
    2014/12/17 Procedure to Repair Front Frame Lift Arm Pin Supports Now Available for R2900G Load Haul Dump Machines {7051}
    Cat® Terrain for Drilling File System
    794 AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) Sensor Supply - Test
    794 AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) Sensor Signal (PWM) - Test
    794 AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) Data Link Configuration Status - Test
    794 AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) Data Link - Test
    980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Differential Backlash and Bearings - Adjust
    994K Wheel Loader Transmission Oil Filter - Replace
    980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Differential Pinion Preload - Adjust
    794 AC Off-Highway Truck VIMSTM 3G and Truck Payload Measurement System (TPMS) Event Codes
    Back to top
    Contacts My AVS
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.