Front Suspension Frame
Show/hide table
| |
| Illustration 1 | g03523319 |
Show/hide table
| Specification for 364-2251 Front Suspension Frame Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| No paint is permitted on mating surfaces. | |||
| 1 | 4 | 6V-7742 Full Nut | Tighten the full nuts for the axle in the mid-travel position. |
| 2 | 2 | 172-6459 Bolt | Prior to installation, prime the cavity (10) with grease. |
| 3 | 1 | 310-9860 Stabilizer | During assembly, ensure that face (A) is at angle (B) of 90 ± 1 degrees to the axis joining the centers of the stabilizer ends. |
| 4 | 1 | 6Y-4457 Bearing | Before assembly, bore is |
| 5 | - | - | Prime the cavity with grease prior to fitting the A-frame onto the machine. |
| 6 | - | - | Before assembly, apply blue Loctite High Flex GM to join the mating surfaces. |
| 7 | 1 | 465-1098 Retainer Collar | Use the following procedure in order to tighten Spherical Bearing: 1. Slide the assembly over the pin. 2. Assemble retainer collar (7) using bolt (8) and hard washer (9). 3. Tighten three bolts equally and incrementally to 4. Use a suitable hammer to strike the retainer collar and apply further torque to the three bolts. 5. Continue to strike the retainer collar and continue to apply torque to the three bolts until no loss of torque is evident. Note: Recheck the torque of the bolts after the road test. |
| 8 | 3 | 6V-5696 Bolt | |
| 9 | 3 | 5P-8245 Hard Washer | |
Caterpillar Information System:
CB44B and CB46B Vibratory Asphalt Compactors Maintenance Interval Schedule
12M Series 3, 140M Series 3 and 160M Series 3 Motor Graders Solenoid Valve - Test
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Transmission Control
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Brake Accumulator (Service)
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Brake Accumulator (Parking)
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Final Drive and Wheel
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Secondary Steering Pump and Electric Motor
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Axle Housing
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Fuel Tank
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Service Brake Lines
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Hydraulic Caliper Service Brake
725C, 725C2, 730C, 730C2 and 730C, 730C2 EJECTOR Articulated Truck Systems Fuel Tank
725C, 725C2, 730C and 730C2 Articulated Truck Systems System Pressure - Release
725C, 725C2, 730C and 730C2 Articulated Truck Systems Machine Preparation for Testing and Adjusting
CB54B Vibratory Asphalt Compactor Maintenance Interval Schedule
966M Series XE and 972M Series XE Wheel Loaders Camera
730C and 730C2 EJECTOR Articulated Truck Systems Operational Checks
725C, 725C2, 730C and 730C2 Articulated Truck Systems Visual Inspection
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Operator Control Switch (Switch to Ground) - Test
AP1000F Asphalt Paver Propel System Piston Pump Flow - Test
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test
Procedure to Install a New Oil Filter Base Assembly on 797 Off-Highway Trucks{4257, 4265, 4269, 5068} Procedure to Install a New Oil Filter Base Assembly on 797 Off-Highway Trucks{4257, 4265, 4269, 5068}
2014/08/27 Rework Procedure to Install a New Oil Filter Base Assembly Is Now Available on Certain 797 and 797B Off-Highway Trucks {4257, 4265, 4269, 5068}
2013/12/20 Improved Product Link Satellite System Special Instruction guide {7606}