Service Tools
The following service tools can be used to aid in troubleshooting the electrical system.
Show/hide table
Service Tools | |
---|---|
Part Number | Part |
(1) | Caterpillar Electronic Technician (Cat ET). |
6V-7070 | Digital Multimeter (HEAVY-DUTY) |
9U-7330 | Digital Multimeter |
146-4080 | Digital Multimeter Gp |
7X-1710 | Multimeter Probe Group |
Show/hide table
(1) | In order to use the Cat ET, order the following materials: Special Publication, JERD2124, "ET Single Use Program License", Special Publication, JEHP1026, "Information and Requirements Sheet", 7X-1425 Data Link Cable and the Data Subscription and Special Publication, JERD2142, "Data Subscription". The Special Publication, JEHP1026, "Information and Requirements Sheet" lists the required hardware and the features of the Cat ET. |
Refer to Testing and Adjusting, "Using Caterpillar Electronic Technician (Cat ET) to Determine Diagnostic Codes" for additional information on Cat ET. Use the digital multimeter for making continuity checks or for measuring voltage. For instructions about the use of the 6V-7070 Digital Multimeter, refer to Special Instruction, SEHS7734. The 7X-1710 Multimeter Probe is used in order to measure the voltage without disconnecting the connector. The probe cables are pushed into the back of the connector along the wire. The 8T-8726 Adapter Cable As has a 3-pin breakout. The adapter cable is used for measurements in the sensor circuits.
Caterpillar Information System:
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) General Information
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) Using Caterpillar Electronic Technician to Determine Diagnostic Codes
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) Diagnostic Code List
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) Event Codes
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) Operational Problems
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) Object Detection Sensor Identification
PM-200 Cold Planer Indicators and Gauges - Test
2013/09/20 Improved Engine Oil Plugs Are Used on Certain C11 and C13 Engines {1326}
PM-200 Cold Planer Hydraulic Tank Breather - Replace
2013/10/10 An Improved Retaining Ring Is Now Available for Machines Equipped with ELRT Transmission Control Valves {3083, 3157}
2014/01/15 A New Shaft with New Pinion in the Circle Drive Group Is Now Used on Certain Motor Graders {5207}
Procedure to Return the Fuel Filter for Certain Caterpillar Equipment{1260, 1261, 1274} Procedure to Return the Fuel Filter for Certain Caterpillar Equipment{1260, 1261, 1274}
773E and 777D Off-Highway Truck/Tractor Object Detection System (Two Cameras) Diagnostic Capabilities
Procedure to Install Gussets on the Front Axle Assembly on Certain 16M Motor Graders{0679, 4313, 5225} Procedure to Install Gussets on the Front Axle Assembly on Certain 16M Motor Graders{0679, 4313, 5225}
PM-200 Cold Planer Legs (Struts) - Lubricate
PM-200 Cold Planer Lower Conveyor Belt (First Stage) Tension and Tracking - Adjust
PM-200 Cold Planer Lower Conveyor Deflectors (First Stage) - Inspect/Replace
PM-200 Cold Planer Hydraulic System Return Filter - Replace
PM-200 Cold Planer Power Take-Off Clutch Oil - Change
PM-200 Cold Planer Power Take-Off Clutch Oil Breather - Clean
PM-200 Cold Planer Power Take-Off Clutch Oil Filter - Replace
PM-200 Cold Planer Power Take-Off Clutch Oil Level - Check
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Vibration Damper - Remove and Install
PM-200 Cold Planer Power Take-Off Clutch Oil Sample - Obtain