Cat® Fleet Onboard v3.x Caterpillar


Operator Utilities for Fuel Truck

Usage:

- DNG

CMPD Fluid Transaction Functionality

New functionality has been added for the operator of a fluid dispensing vehicle. Select the fluid type from a list and enter the quantity of fluid being dispensed to a target machine. The new window will allow an operator to select only one target machine from a list. The list of machines is sorted based on GPS proximity only when machine positions are available via the "AllMachinePosition" message. Machines can be sorted alphabetically, when machine positions are not available.



    Illustration 1g03431260

  1. Press "Tab" button to access "Fluids" screen

    A screen similar to 1 will appear.

    Note: Use only the touch screen to make entries on the "Fluids" Screen.



    Illustration 2g03431357

  2. Select the machine to service from the "ID" drop-down menu.


    Illustration 3g03431374

  3. Enter the hours of the machine to be serviced in the "SMU" keypad window.


    Illustration 4g03431392

  4. Select the "CATEGORY".


    Illustration 5g03431439

  5. Select the "ITEM".


    Illustration 6g03431463

  6. Select "QUANTITY" and enter the amount dispensed into the keypad.


    Illustration 7g03431472

  7. Press "Add" to add the item dispensed to the list.

  8. Repeat these steps to add additional fluids to the same machine.


    Illustration 8g03431477

  9. Press "Send" to send list to the office when servicing is completed.


    Illustration 9g03432486

  10. Verify the completion of this transaction by pressing "Yes"

    Note: The list will clear automatically.



Illustration 10g03432510
Screen shot to clear entire list


Illustration 11g03432521
Screen shot to clear line entry

An item can only be entered once per list. If additional amount of the same item is to be added during the same transaction, the original item line must be deleted and re-entered with the total amount. You are able to clear the entire list, refer to Illustration 10. If removal of one line is needed, refer to Illustration 11.

Caterpillar Information System:

836K Landfill Compactor and 834K Wheel Dozer Machine Systems Steering Neutralizer Valve - Remove and Install
2013/10/21 The Cab Wiring Group Has Been Improved on Certain 793F, 795F AC , and 797F Off-Highway Trucks {1408}
CB22B, CB24B, CB32B and CC24B Vibratory Utility Compactors Propel System Propel Lines Group
2013/09/16 Procedure for Improving Antenna Communication on All Machines Equipped With Product Link {733B, 7606}
CB22B, CB24B, CB32B and CC24B Vibratory Utility Compactors Propel System Propel Lines Group
CB36B Asphalt Compactor and CB34B, CB34B XW and CC34B Vibratory Utility Compactors Propel System Motor Support (Drum Propel)
CB36B Asphalt Compactor and CB34B, CB34B XW and CC34B Vibratory Utility Compactors Propel System Motor Support (Drum Propel)
259D, 279D, 289D, 299D, 299D XHP, 299D2 and 299D2 XHP Compact Track Loaders, 257D, 277D, 287D, 297D, 297D XHP, 297D2 and 297D2 XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D, 272D XHP, 272D2 and 272D2 XHP Skid Steer Loaders Air Conditioner Lines
Procedure to Flash Laser Detection And Ranging (LADAR) Firmware{7600} Procedure to Flash Laser Detection And Ranging (LADAR) Firmware{7600}
PM-200 Cold Planer Access Doors and Covers
AP1000F Asphalt Paver Machine Systems Conveyor Drive Chain (Drag) - Check and Adjust
PM-200 Cold Planer Lifting and Tying Down the Machine
2013/09/27 New Start Switch Assembly Is Now Used on the 770G and 772G Off-Highway Trucks {1408, 1416, 7301}
2013/12/04 The Brake Oil Cooler Lines Group Has Been Improved on 770G and 772G Off-Highway Trucks {0679, 4257, 5057, 7051}
988K XE Wheel Loader Machine Systems Steering Cylinder - Remove and Install
2013/09/18 Parts Ordering for the Mid-Mount Scarifier Bracket Has Been Clarified on Certain M and M Series 2 Motor Graders {6162, 7000}
AS4173 Asphalt Screed Machine Systems Heater Element - Test
The Quick Disconnect Fitting for the Service Group is Failing on Certain Cat Machines{1325, 1710, 4283, 7000, 7513} The Quick Disconnect Fitting for the Service Group is Failing on Certain Cat Machines{1325, 1710, 4283, 7000, 7513}
A New Cylinder Head is Now Used for Certain R1300G and R1300GII Underground Mining Machines {1100} A New Cylinder Head is Now Used for Certain R1300G and R1300GII Underground Mining Machines {1100}
988K XE Wheel Loader Machine Systems Gear Pump (Secondary Steering) - Disassemble
988K XE Wheel Loader Machine Systems Gear Pump (Secondary Steering) - Assemble
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Steering Spool Does Not Respond
2013/10/17 A New Shaft with New Pinion in the Circle Drive Group is Now Used on Certain 14M Motor Graders {5207}
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Implement Electronic Control System Steering Spool Response Is Unexpected
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.