Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-1860 | Retaining Ring Pliers | 1 |
B | 1U-9200 | Lever Puller Hoist | 1 |
C | 140-7742 | Sleeve | 2 |
D | 1P-1831 | Bearing Puller Adapter | 1 |
FT-1410 | Sleeve | 1 | |
4K-0684 | Hard Washer | 1 | |
9U-5345 | Nut | 1 | |
9U-5343 | Puller Stud | 1 | |
350-7768 | Hydraulic Pump | 1 | |
6V-3160 | Double Acting Cylinder | 1 | |
E | 1P-1834 | Bearing Puller Adapter | 1 |
FT-1410 | Sleeve | 1 | |
4K-0684 | Hard Washer | 1 | |
9U-6833 | Nut | 1 | |
4C-9633 | Puller Stud | 1 | |
350-7769 | Hydraulic Pump | 1 | |
6V-3160 | Double Acting Cylinder | 1 |
Start By:
- Remove the tilt cylinder.
- Remove the bucket.
- Place suitable cribbing under the front of lift arms (1).
Show/hide table
Illustration 2 g01247934 - Attach a suitable lifting device to the rod end of lift cylinder (4). The weight of lift cylinder (4) is approximately
60 kg (132 lb) . Use Tooling (A) in order to remove retaining ring (2). Remove pin assembly (3). Use the suitable lifting device in order to lower the rod end of lift cylinder (4) away from lift arms (1). Repeat for the other side.Show/hide tableIllustration 3 g01383329 - Disconnect hose assemblies (5) and (6) from each side of the machine.
Show/hide table
Illustration 4 g01383339 - Cut cable straps (7) and disconnect harness assembly (8). Place harness assembly (8) to the side.
Show/hide table
Illustration 5 g03210058 - Attach Tooling (B), Tooling (C), and a suitable lifting device to lift arms (1). The weight of lift arms (1) is approximately
460 kg (1015 lb) .Show/hide tableIllustration 6 g03210062 Show/hide tableIllustration 7 g01383377 - Remove plate (9). Repeat for other side.
- The weight of pin (10) is approximately
27 kg (60 lb) . Use two people to remove pin (10). - Remove lift arms (1).
Show/hide table
Illustration 8 g01248263 Show/hide tableIllustration 9 g03210122 Show/hide tableWhen you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
- Use Tooling (D) in order to remove bearings (11).
Show/hide table
Illustration 10 g01248265 Show/hide tableIllustration 11 g03210126 Show/hide tableWhen you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
- Use Tooling (E) in order to remove bearings (12).
Show/hide table
Illustration 12 g01248315 - Remove bearings (13).
Illustration 1 | g01247933 |