Travel Speed - Check
Show/hide table
机器突然动作,会导致人员伤亡。 机器突然移动,会对机上或机器近处的人员造成伤害。 为避免伤亡事故,开动机器之前,确保机器周围无人及没有各种障碍物。 |
Show/hide table
旋转和移动零件会造成人身伤害。 旋转的风扇叶片和运动的零件会甩出或切削任何掉入或推向其前的物体或工具。 确保没有人员在运行的发动机上、下方或附近作业。 应确认机器周围没有其他人。 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 说明 | 数量 |
A | 348-5430 | 多用工具总成 | 1 |
B | N/A | 秒表 | 1 |
- 设置一个
30.5 m (100 ft) 直行速度测试场。 确保该行程为机器提供了充足的距离以在越过起跑线前达到全速,并为机器提供了充足的距离以在越过终点线后停止。 该行程应为无斜坡的平缓坚固路面。 - 驱动机器到测试区域。
Show/hide table
图 1 g02982451 - 将行驶操纵杆 (1) 移至空档位置。
- 将停车制动器开关 (2) 移到 ON(接通)位置。
Show/hide table
图 2 g02982455 - 在低怠速下运行发动机数分钟。 使用油门控制开关 (3),以便在高怠速下操作发动机。
注: 当发动机处于高怠速时,有两个指示。 首先,显示屏上将显示"高怠速"。 其次,紧邻油门控制开关 (3) 的第三个 LED 将点亮。
- 使用工具 (A) 监控液压油温。 操作机器直至油温达到
38 °C (100 °F) 。Show/hide table图 3 g02982458 - 使用行驶模式开关 (5),以便将行驶马达切换至高速位置。
注: 当行驶马达位于高速位置时,有两个指示。 首先,显示屏上将显示"高速行驶模式"。 其次,紧邻行驶模式开关 (5) 的两个 LED 将点亮。
- 使用增速开关 (4),以便将行驶速度设定到 100%。
注: 当行驶速度设定为 100% 时,有两个指示。 首先,显示屏上将显示"速度控制 % 100"。 其次,紧邻增速开关 (4) 的七个 LED 将点亮。
- 将停车制动器开关 (2) 移到断开位置。
- 将机器后退足够远以在起跑线前达到全速。
- 记下机器通过
30.5 m (100 ft) 测试场的时间。 可接受行驶时间为 9.6 ± 1 秒。 - 倒退行驶重复该测试。 前进和后退时间各自应在 1 秒内。
- 使用行驶模式开关 (5),以便将行驶马达切换至低速位置。
注: 当行驶马达位于低速位置时,有两个指示。 首先,显示屏上将显示"低速行驶模式"。 其次,紧邻行驶模式开关 (5) 的一个 LED 将点亮。
- 重复前进和后退测试。 可接受前进行驶时间为 19.2 ± 1 秒。 前进和后退行驶时间各自应在 1 秒内。
- 把机器开到平整水平的路面。
- 将行驶操纵杆 (1) 移至空档位置。
- 将停车制动器开关 (2) 移到 ON(接通)位置。
- 使用油门控制开关 (3),以便在经济模式或低怠速下操作发动机。
注: 当发动机处于经济模式时,有两个指示。 首先,显示屏上将显示"经济"。 其次,紧邻油门控制开关 (3) 的第二个 LED 将点亮。 当发动机处于低怠速时,有两个指示。 首先,显示屏上将显示"低怠速"。 其次,紧邻油门控制开关的第一个 LED 将点亮。
Show/hide table图 4 g02982462 - 将发动机起动开关 (6) 移到断开位置。
Caterpillar Information System:
725C2 Articulated Truck Lubricant Viscosities - Fluids Recommendations
836K Landfill Compactor Transmission Oil - Change
586C Site Prep Tractor Power Train Hydraulic Tank
Cat® Fleet Onboard Software Version 3.1 Antenna - Check/Clean
725C Articulated Truck Retarder Control
Hydraulic System Cleanup Recommendations Following Catastrophic Component Failures on Wheel Loader Hydraulic Systems {0645, 0680, 0738, 0768, 5050, 5056, 5095} Hydraulic System Cleanup Recommendations Following Catastrophic Component Failures on Wheel Loader Hydraulic Systems {0645, 0680, 0738, 0768, 5050, 5056, 5095}
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Engine Supplement Electric Starting Motor - Remove and Install
725C2 Articulated Truck Body Support
836K Landfill Compactor Transmission Oil Sample - Obtain
CD44B Vibratory Asphalt CompactorMachine Systems Piston Pump (Propel, Vibratory) - Remove and Install
836K Landfill Compactor Transmission Oil Level - Check
CP74B, CS74B, CS76B, CS78B and CS79B Vibratory Soil Compactors Propel System Case Drain Flow for Piston Motor (Drum Propel) - Test
725C2 Articulated Truck Tire Inflation - Check
836K Landfill Compactor Turbocharger - Inspect
416F, 420F, 422F, 428F, 430F, 432F, 434F and 444F Backhoe Loaders Engine Supplement Refrigerant Condenser - Remove and Install
CP74B, CS74B, CS76B, CS78B and CS79B Vibratory Soil Compactors Propel System Flushing Valve (Axle Propel Motor, Drum Propel Motor) - Test and Replace
Release Notes for Cat® Terrain v4.5 On-board Software{7605} Release Notes for Cat® Terrain v4.5 On-board Software{7605}
R1700G Load Haul Dump Maintenance Interval Schedule
R1600H Load Haul Dump Machine Systems Accumulator Charging Valve (Brake) - Assemble
R1600H Load Haul Dump Machine Systems Accumulator Charging Valve (Brake) - Install
R1600H Load Haul Dump Machine Systems Brake Control Valve (Service) - Remove
R1600H Load Haul Dump Machine Systems Brake Control Valve (Service) - Install
R3000H Load Haul Dump Hydraulic System Relief Valve (Lift Circuit)
R1600H Load Haul Dump Machine Systems Brake Release Cylinder - Remove