Hydraulic System Oil and Filters - Change
Cat HYDO Advanced 10 Oil Change Interval
The standard Cat HYDO Advanced 10 oil change interval is every 3000 service hours or 2 years.
Procedure to Change the Hydraulic Oil
- Remove hydraulic tank cap (3) in order to relieve pressure from the hydraulic system.
Show/hide table
Illustration 2 g02476017 (6) Material feed filter
(7) Drain hose - The drain hose (7) for the hydraulic tank is located in the right side access door. Remove the plug from the drain hose, and drain the hydraulic oil into a suitable container.
Note: Refer to Operation and Maintenance Manual, "General Hazard Information" for information on containing fluid spillage.
- Remove the cover for the charge filter (1). Remove the charge filter.
- Remove the return filter cover (5). Remove the return filter.
- Remove material feed filter (6).
- Install the drain plug.
- Install a new charge filter. Install the cover for the charge filter (1).
- Install a new return filter. Install the return filter cover (5).
- Install a new material feed filter (6).
- Fill the hydraulic tank. Refer to the Operation and Maintenance Manual, "Capacities (Refill)" for the correct refill capacity.
- Install hydraulic tank cap (3).
- Start the engine. Run the engine for a few minutes. Check the hydraulic filters for leaks.
- Stop the engine.
- Repair the leaks that were found.
- Maintain the oil between the "FULL" and "ADD" marks on oil level gauge (2).
Show/hide table
Illustration 1 | g02425457 |
(1) Charge filter
(2) Hydraulic oil level gauge (3) Hydraulic tank cap (4) Return filter indicator (5) Return filter |
Caterpillar Information System:
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Fumes Disposal Filter Element - Replace
Procedure and Guidelines for Cleaning Phosphate Coated Track Pins {4169, 4171, 7950} Procedure and Guidelines for Cleaning Phosphate Coated Track Pins {4169, 4171, 7950}
Procedure for Water-Cooled Welding of Track Rollers {0679, 4180, 7950} Procedure for Water-Cooled Welding of Track Rollers {0679, 4180, 7950}
2011/03/07 A New Procedure to Update the Accumulator Lines GP on Certain 773F and 775F Off-Highway Trucks is Available {4257, 4263, 5068}
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Engine Mounts - Inspect
770G and 772G Off-Highway Truck Power Train Torque Converter Lockup Clutch Leakage - Test
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Cooling System Water Temperature Regulator - Replace
AP1000E Asphalt Paver Equipped with a Cat C6.6 Engine Cooling System Coolant Extender (ELC) - Add
770G and 772G Off-Highway Truck Systems Windshield Wiper Motor - Test
EMCP 3 to EMCP 4.1/4.2 Cat ® Retrofit Instructions{4490} EMCP 3 to EMCP 4.1/4.2 Cat ® Retrofit Instructions{4490}
AS3301C Asphalt Screed Maintenance Interval Schedule
AS2302C Asphalt Screed Maintenance Interval Schedule
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Pump Drive Breather - Clean
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Track Roller Bearings - Inspect
AP1055E and BG1055E Asphalt Pavers Equipped with a Cat C7.1 Engine Track Roller Bearings - Lubricate
Mobil-TracSystems/MTS {4198} Mobil-TracSystems/MTS {4198}
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Tamper Bar) - Remove
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Tamper Bar) - Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Right Drag Conveyor and Right Auger Conveyor) - Remove
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Right Drag Conveyor and Right Auger Conveyor) - Install
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Left Drag Conveyor and Left Auger Conveyor) - Remove
AP1000E and BG1000E Asphalt Pavers Machine Systems Piston Pump (Left Drag Conveyor and Left Auger Conveyor) - Install
Installation of Alternative Seat Height Adjustment Valve{7312, 7324} Installation of Alternative Seat Height Adjustment Valve{7312, 7324}
725C2 Articulated Truck Windows