Fuel Priming Pump and Fuel Filter Base - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 为便于安装,在所有软管、所有软管组件、所有导线及所有管组件上作出识别标记。 塞住所有软管组件和管组件。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将燃油供应转到断开位置。
Show/hide table
图 1 | g01318612 |
典型示例 |
- 将蓄电池断路开关转到断开位置。
- 从注油泵 (3) 上断开塑料管组件 (4) 和 (5) 。
- 从注油泵 (3) 上断开塑料管组件 (4) 和 (5) 。
- 从注油泵 (3) 上断开塑料管组件 (2) 。
- 塞住注油泵 (3) 及塑料管组件 (4) 和 (5) 上的所有接头。
- 从注油泵 (3) 上断开线束组件。
- 支承住注油泵。 卸下螺栓和垫圈 (1) ,然后卸下注油泵 (3) 。
注: 记录管组件支架的位置和方向。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 2 | g01318612 |
典型示例 |
- 确保燃油注油泵清洁、无磨损或损坏。 如有必要,作为一整个组件更换注油泵。
- 将注油泵 (3) 定位到缸盖上。 安装螺栓和垫圈 (1) 。 确保所有螺栓固定的支架安装位置正确。 拧紧螺栓至扭矩为 9 N·m (80 lb in)。
- 从注油泵和塑料管组件上卸下所有塞。 将塑料管组件 (4) 和 (5) 连接到注油泵 (3) 上。
- 将塑料管组件 (2) 连接到注油泵 (3) 上。
- 将线束组件安装到注油泵 (3) 上。
- 将燃油供应转到接通位置。
- 将蓄电池断路开关转到接通位置。
- 排出燃油系统中的空气。 请参阅操作和保养手册, "燃油系统 - 充油"。
Caterpillar Information System:
2007/05/28 An Improved Battery Isolation Control is Now Used {1402, 1408}
2009/08/24 An Improved Solenoid Valve Group Is Used In Transmissions With ICM For Increased Reliability And Longer Service Life {3124, 3167, 3174}
IT38H Integrated Toolcarrier and 938H Wheel Loader Steering System Secondary Steering System
2007/08/27 A New Temperature Gauge is Used {7450}
16M Motor Grader Machine Systems Front Frame to Rear Frame (Articulating Hitch) - Connect
Installing the 307-6237 Roading Lights Mounting Gp (KIT) (GERMANY) (ITALY){1429} Installing the 307-6237 Roading Lights Mounting Gp (KIT) (GERMANY) (ITALY){1429}
16M Motor Grader Machine Systems Front Frame from Rear Frame (Articulating Hitch) - Separate
450E Backhoe Loader Machine Systems Bank Valve (Backhoe) - Remove
450E Backhoe Loader Machine Systems Bank Valve (Loader) - Install
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Manifold (Pilot Operated) - Inlet Manifold for the Backhoe
Installation of the AccuGrade® - Grade Control System for the Motor Graders{7220} Installation of the AccuGrade® - Grade Control System for the Motor Graders{7220}
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0681 - FMI 06
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Lines - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector Cover - Remove and Install
C6.6 Engines For Caterpillar Built Machines CID 2417 FMI 05
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Remove
C6.6 Engines For Caterpillar Built Machines CID 2417 FMI 06
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Pump Gear - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Pump Gear - Install
C6.6 Engines For Caterpillar Built Machines CID 2770 FMI 03
770 and 772 Off-Highway Trucks Engine Supplement Alternator - Remove and Install
Test and Repair for Excessive Current Draw{1401, 1408} Test and Repair for Excessive Current Draw{1401, 1408}
2007/08/06 New Water Lines Groups Are Available {1380}