Aftercooler - Install
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | FT-2515 | Guide Bolt | 2 |
| B | 138-7575 | Link Bracket | 2 |
- Attach a suitable lifting device to aftercooler (6). Position aftercooler (6). The weight of aftercooler (6) is approximately
25 kg (55 lb) .Show/hide table
Illustration 2 g01303388 - Position clamps (4). Tighten clamps (4) to a torque of
7.5 ± 1 N·m (66 ± 9 lb in) . - Repeat Steps 1 through Step 2 for the remaining aftercooler.
Show/hide table
Illustration 3 g01303379 - Attach Tooling (B) and a suitable lifting device to hand hold (3). The weight of hand hold (3) is approximately
25 kg (55 lb) . Install Tooling (A). Remove Tooling (B).Show/hide table
Illustration 4 g01303369 - Install bolts (2). Remove Tooling (A).
Show/hide table
Illustration 5 g01303355 - Install bolts (1).
Show/hide table
| |
| Illustration 1 | g01303391 |
Caterpillar Information System:
AccuGrade® Laser Diagnostic Capabilities
450E Backhoe Loader Hydraulic and Steering System Bank Valve (Eight) (Pilot Operated)
AccuGrade® Laser Service Tools
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Low Supply Voltage IQAN MDM
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install - Mechanical Fuel Transfer Pump
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install - Electrical Fuel Transfer Pump
C11 and C13 Engines and 14M and 16M Motor Graders Injector Solenoid - Test
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Engines with Flywheel Housing and Back Plate
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
2006/12/04 Improved Signal Lamp for the Stop, Tail and Turn Signal Lights Is Used {1430, 1432}
450E Backhoe Loader Hydraulic and Steering System Bank Valve (Eight) (Mechanically Operated)
AccuGrade® Laser Operational Problems
777E, 777F and 777G Off-Highway Truck Refrigerant Compressor - Remove and Install
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes RTC+ Not Connected IQAN MDM
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes CHECKSUM Error IQAN MDM
814F Series 2 Wheel Dozer, 815F Series 2 Soil Compactor and 816F Series 2 Landfill Compactor Power Train Torque Converter Stall - Test
AccuGrade® Laser Diagnostic Code List
C11 and C13 Engines and 14M and 16M Motor Graders Sensor Signal (Analog, Active) - Test
2006/11/27 An Updated Gasket for the Water Temperature Regulator Housing is Available {1355, 1380, 1393}
2006/11/27 An Updated Gasket for the Water Temperature Regulator Housing is Available {1355, 1380, 1393}
450E Backhoe Loader Hydraulic and Steering System Hydraulic Hand Control (Backhoe)
AS3251C Asphalt Paver Chain (Crown) - Remove and Install