A New Saw Pump Is Used on Track Feller Bunchers {5070}
- Track Feller Buncher:
- TK711 (S/N: 1011-213)
- TK721 (S/N: 1021-213)
- TK722 (S/N: 1031-216)
- TK732 (S/N: 1041-201)
- TK741 (S/N: 2021-192)
- TK751 (S/N: 3011-261)
- TK752 (S/N: 3021-337)
- 1090 (S/N: BZJ1-206)
- 1190 (S/N: BZK1-206)
- 1190T (S/N: BZL1-208)
- 1290T (S/N: BZM1-207)
Description of Change:
Show/hide table
Illustration 1 | g01298133 |
A new saw pump is used on the Track Feller Buncher models that are listed above. The new saw pump has been improved in order to increase the reliability of the pump. These improvements include the following:
- an improved shaft seal
- a center support for the piston slipper
- a thicker slipper retainer
- increased clearances in the bores
Adaptable To: The new 268-8259 Piston Pump Gp has replaced the former 218-2977 Piston Pump Gp. The new pump is adaptable to the machines that are listed above. The new pump is effective with the machines that are listed in Table 1.
Show/hide table
Model Number     | Serial Number     |
TK711     | S/N:101245-UP     |
TK721     | S/N:102345-UP     |
TK722     | S/N:103217-UP     |
TK732     | S/N:104202-UP     |
TK741     | S/N:202193-UP     |
TK751     | S/N:301262-UP     |
TK752     | S/N:302338-UP     |
1090     | S/N:BZJ207-UP     |
1190     | S/N:BZK1220-UP     |
1190T     | S/N:BZL1320-UP     |
1290T     | S/N:BZM208-UP     |
Show/hide table
First Position     | Second and Third Positions     | Fourth Position     | Fifth Position through Seventh Position     |
A= January     | The numbers in these positions indicate the day of the month.     | T= 2004     | Sequence number     |
B= February     | |||
C= March     | |||
D= April     | |||
E= May     | U= 2005 | ||
F= June     | |||
G= July     | |||
H= August     | |||
I= September     | V= 2006 | ||
J= October     | |||
K= November     | |||
L= December     |
Caterpillar Information System:
C-9 Engines for Caterpillar Built Machines Speed/Timing Sensor
PL61 Pipelayer Fuel System Primary Filter - Clean/Replace
C15 Petroleum Generator Set Engines Inlet Air Temperature Sensor
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XT2 A0-25
793D Off-Highway Truck Power Train Flow Control and Relief Valve (Rear Axle Oil) - Assemble
793D Off-Highway Truck Power Train Flow Control and Relief Valve (Rear Axle Oil) - Disassemble
572R Series II Pipelayer Transmission Magnetic Screen - Clean
Procedure for Kidney Looping Wheel Harvester and Site Prep Tractor Hydraulic Oil{0680, 0738, 0768, 3000, 5050, 5056} Procedure for Kidney Looping Wheel Harvester and Site Prep Tractor Hydraulic Oil{0680, 0738, 0768, 3000, 5050, 5056}
2006/08/14 An Improved Weld Is Now Used on the Undercarriage on Track Feller Bunchers {4150}
16M Motor Grader Transmission and Differential Oil Level - Check
793D Off-Highway Truck Power Train Transmission Hydraulic Control - Install
793D Off-Highway Truck Power Train Transmission Hydraulic Control - Remove
IT38H Integrated Toolcarrier and 938H Wheel Loader Axle Oil Cooler Magnetic Filter - Clean/Replace
IT38H Integrated Toolcarrier and 938H Wheel Loader Cab Air Filter - Clean/Replace
AS2302 Screed Extender Carriage
777G Off-Highway Truck Power Train Duo-Cone Seals - Install
2006/11/06 New Seal Kit for Fan Motors {1386, 5061}
PM-201 Cold Planer Rotor Coolant Level - Check - Drum with Three-Piece Rotor Bits
IT38H Integrated Toolcarrier and 938H Wheel Loader Engine Crankcase Breather - Clean - If Equipped
IT38H Integrated Toolcarrier and 938H Wheel Loader Fuel Tank Water and Sediment - Drain
120M, 12M, 140M and 160M Motor Graders Power Train Pressure Switch (Parking Brake)
770, 772, 773E, 773F, 777E and 777F Off-Highway Trucks and 775F Quarry Truck VIMS Truck Payload System Connector Contact Description
PM-200 Cold Planer Rotor Cutter Bits - Inspect/Replace - Drum with Three-Piece Rotor Bits
120M, 12M, 140M and 160M Motor Graders Power Train Solenoid Valve (Parking Brake)