Tire and Rim (Rear) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 9U-7489     | 起吊台架     | 2     |
4C-5809 | 电动液压泵     | 1     | |
B     | 194-7586     | 气动扳手总成     | 1     |
194-7886 | 驱动延长件     | 1     | |
4C-6723 | 套筒     | 1     | |
C     | 138-7576     | 连杆支架     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
按照建议的步骤拆卸和安装轮胎和/或车轮组件。 确保始终正确支撑住机器以及轮胎和/或车轮组件。 采用不正确的步骤拆卸和安装轮胎和/或车轮组件可造成人员伤亡。 |
Show/hide table
维修和更换轮胎和轮辋是危险的。 此工作只能由受过培训的人员使用正确的工具和步骤才能完成。如果不用正确的程序维修轮胎和轮辋,总成可能在爆炸力下裂开从而造成严重的人身伤亡。仔细阅读轮胎维修人员或代理商提供的技术参数信息。 |
注: 彻底清洁车轮的加工安装面,然后安装轮胎和轮缘。 清除任何油漆、碎屑和其他污染物。
- 使用适当的轮胎装卸机定位轮胎和轮缘 (11) 。 轮胎和轮缘 (11) 的重量约为 5159 kg (11374 lb)。
注: 使用拆卸步骤中制造的标记将轮缘对准终传动。
Show/hide table
图 1 | g01276005 |
Show/hide table
图 2 | g01276000 |
- 使用工具 (B) 安装两个螺母 (10) 。
- 拆下轮胎装卸机。
- 使用工具 (B) 安装螺母 (10) 。 将螺母 (10) 上紧到 1000 ± 125 N·m (738 ± 92 lb ft) 的扭矩。
Show/hide table
图 3 | g01276334 |
- 定位软管组件 (9) ,然后安装支架 (8) 。
Show/hide table
图 4 | g01275987 |
- 将轮胎和轮缘 (5) 放在适当的垫块上。
Show/hide table
图 5 | g01276151 |
- 将工具 (C) 和适当的起吊设备连接到环 (6) 上。 环 (6) 的重量约为 127 kg (280 lb)。
Show/hide table
图 6 | g01275928 |
- 安装环 (6) 。
- 安装螺母 (7) 。 将螺母 (7) 上紧到 1000 ± 125 N·m (738 ± 92 lb ft) 的扭矩。
- 使用适当的轮胎装卸机定位轮胎和轮缘 (5) 。 轮胎和轮缘 (5) 的重量约为 5159 kg (11374 lb)。
Show/hide table
图 7 | g01275897 |
Show/hide table
图 8 | g01275898 |
- 使用工具 (B) 安装两个螺栓 (4) 。
- 拆下轮胎装卸机。
- 使用工具 (B) 安装其余的螺栓 (4) 。 将螺栓 (4) 上紧到 900 ± 100 N·m (664 ± 74 lb ft) 的扭矩。
Show/hide table
图 9 | g01275876 |
- 安装支架 (3) 和隔套。 定位阀 (2) 并安装螺栓 (1) 。
Show/hide table
图 10 | g01275671 |
- 使用工具 (A) 降低机器后部。 请参阅操作和保养手册, "顶起部位 - 机器后部"。
Show/hide table
图 11 | g01275656 |
- 检查轮胎压力。 请参阅操作和保养手册, "轮胎充气压力调整"和操作和保养手册, "轮胎氮气充气"。
End By: 取走车轮楔子。 请参阅 拆解和组装, "车轮楔子(前和后)- 拆卸和安装"。
Caterpillar Information System:
793D Off-Highway Truck Power Train Tire and Rim (Rear) - Remove
Starting and Charging Systems Test Considerations
Installing a Ride Control Kit{1408, 5004, 5057, 5077} Installing a Ride Control Kit{1408, 5004, 5057, 5077}
Starting and Charging Systems Troubleshooting
R1700G Load Haul Dump Steering System Diverter Valve (Steering Release)
R1600G Load Haul Dump Steering System Diverter Valve (Steering Release)
R1700G Load Haul Dump Brake Release - If Equipped
Starting and Charging Systems Test Step D, High Idle
Starting and Charging Systems Test Step C, Start Aid
2007/04/30 A New Valve Improves the Service Life of the Circle Drive Motors {5057, 5082, 5207}
Machine Start Switch Key May Not Fit Properly{1416} Machine Start Switch Key May Not Fit Properly{1416}
Starting and Charging Systems Test Step B, Crank
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Control Valve (Hood Tilt, Manual Brake Release)
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Control Valve (Parking and Rotor Brake Release)
C27 and C32 Engines for Caterpillar Built Machines Mass Air Flow Sensor
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 0713 - FMI 03
2006/06/05 New Exhaust Temperature Sensors Are Now Used {1919}
990K Wheel Loader Electronic Unit Injector - Inspect/Adjust
2006/10/23 An Improved Torque Converter Turbine is Now Used In the Torque Converter Group {3101}
Starting and Charging Systems Starter Ground Circuit Test Description
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Pressure Sensor
3176C Engines for Caterpillar Built Machines Engine Pressure Sensor Open or Short Circuit - Test
3508 EUI Engine for Off-Highway Truck/Tractors Turbocharger Outlet Pressure Sensor
Field Installation of the 264-0187 Ride Control Installation Gp {1408, 5004, 5057, 5077} Field Installation of the 264-0187 Ride Control Installation Gp {1408, 5004, 5057, 5077}