Increment Switch
Note: The "Increment Switch Adjustment" dialog is a site selectable feature. Consult your site manager in order to turn this feature ON.
If this feature is turned ON, the "Increment Switch Adjustment" dialog is used in order to set the amount each press of the vertical offset buttons increases or decreases the vertical offset.
To set both the "Increment Switch Adjustment" and the "Target Cross Slope Increment" complete the following steps:
- Press the "Setup Menu" Soft Key.
- Press "Setup Menu - Configuration".
Press the up arrow or the down arrow until "Vertical Offset Switch Increment" is highlighted.
- Press the "OK" key.
The dialog that is shown in Illustration 1 is shown.
Note: If your system is configured as a Dual GPS system, the dialog that is shown in Illustration 2 is shown.
Complete one of the following steps:
- Press the arrow keys in order to enter the amount that each press of the vertical offset buttons will increases or decreases the vertical offset.
- Press the "Default 0.05" soft key in order to set the system default. The system default is 0.010 m (0.05 ft).
Note: If your system is configured as a Dual GPS system, skip Step 4.
Show/hide table
Illustration 1 | g01248546 |
Show/hide table
Illustration 2 | g01231979 |
- Press the "Next" key to highlight the "Target Cross Slope Increment" field.
Complete one of the following steps:
- Press the arrow keys in order to enter the amount that each press of the vertical offset buttons will increases or decreases the vertical offset.
- Press the "Default 0.1%" soft key in order to set the system default. The system default is "0.1%".
Show/hide table
Illustration 3 | g01231981 |
- Press the "OK" key in order to save the settings and return to the "Setup Menu-Configuration" dialog.
- Press the "ESC" key in order to exit the "Plan View". The changes take effect immediately.
Caterpillar Information System:
AccuGrade® GPS Using The CD550A Display (GPS/ATS/Sonic/Cross Slope) Sensor Firmware Upgrade
777F Off-Highway Truck Steering System Steering Link
777E and 777F Off-Highway Truck Power Train Oil Filter (Transmission Charging)
AccuGrade® GPS (CD700) Receiver
C15 Petroleum Generator Set Engines Fuel Temperature Sensor
C7 Engine for the AP-755 Asphalt Paver and the PM-102 Cold Planer Digital Sensor Supply Circuit - Test
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Extendable Stick Cylinder - Remove and Install
587R Pipelayer Power Train Track Adjuster - Assemble
587R Pipelayer Power Train Track Adjuster - Disassemble
120M, 12M, 140M and 160M Motor Graders Machine Systems Blade Lift
AccuGrade® GPS (CD700) Operational Problems
777F Off-Highway Truck Oil Filter (Parking Brake Release) - Replace
AccuGrade® GPS Using The CD550A Display (GPS/ATS/Sonic/Cross Slope) Mast Tilt - Adjust Bolt Hole
2006/03/13 Reminder: Operators must be Aware of Possible Work Tool Interference with the Cab {7405}
C15 and C18 Engines for Caterpillar Built Machines Cat Data Link Circuit - Test
120M and 12M Motor Graders Braking and Hydraulic Fan System Introduction
EquipmentManager User Guide Manage Time Fence and Geographic Fence
R1700G Load Haul Dump Hydraulic System Relief Valve (Main) - Test and Adjust
R1700G Load Haul Dump Braking System Accumulator Charging Valve (Brake)
R1700G Load Haul Dump Braking System Brake Accumulator
R1700G Load Haul Dump Power Train Torque Converter Hydraulic System
R1700G Load Haul Dump Braking System Brake Control Valve (Service)
R1700G Load Haul Dump Hydraulic System Relief Valve (Line) - Test and Adjust
R1700G Load Haul Dump Steering System Steering System (Pilot Oil)