Illustration 1 | g01862793 |
Illustration 2 | g01859277 |
There are several specific safety messages on these machines. The exact location of the messages and the description of the messages are reviewed in this section. Please become familiarized with all safety messages.
Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the safety messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.
Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a safety message on the replacement part. Any Caterpillar dealer can provide new safety messages.
Do Not Operate (1)
This warning is located beneath the operator console.
g01370904 |
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility. |
Steering Distance (2)
This warning is located on the operator console.
g01861267 |
Steering performance is slower with cold hydraulic oil which could result in a collision or run over causing serious injury or death. Do not operate the machine until the oil has reached operating temperature. |
Product Link (3) (If Equipped)
This warning is located beneath the operator console.
g01370917 |
This machine is equipped with a Caterpillar Product Link communication device which should be deactivated in or near a blasting zone in compliance with applicable legal requirements. Failure to do so could cause interference with blasting operations resulting in serious injury or death. |
Seat Belt (4)
This warning is located beneath the operator console.
g01370908 |
A seat belt should be worn at all times during machine operation to prevent serious injury or death in the event of an accident or machine overturn. Failure to wear a seat belt during machine operation may result in serious injury or death. |
Engine Coolant (5)
This warning is located on the shunt tank next to the filler cap.
g01371640 |
Pressurized system: Hot coolant can cause serious burn. To open cap, stop engine, wait until radiator is cool. Then loosen cap slowly to relieve the pressure. |
ROPS/FOPS Structure (6)
This warning is located on the lower left side of the ROPS.
g01212098 |
Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a Caterpillar dealer to determine this structure's limitations without voiding its certification. |
This machine has been certified to the standards that are listed on the certification film for the ROPS. The maximum mass of the machine, which includes the operator and the attachments without a payload, should not exceed the mass on the certification film for the ROPS.
A typical example of the warning film and certification film for the ROPS are shown above.
Refer to Operation and Maintenance Manual, "Guards (Operator Protection)" for more information.
Battery (7)
This warning is located near the remote jump start terminal.
g01409730 |
Explosion Hazard! Improper jumper cable connections can cause an explosion resulting in serious injury or death. Batteries may be located in separate compartments. Refer to the Operation and Maintenance Manual for the correct jump starting procedure. |
No Ether (8)
This warning is located in the right side of the engine compartment on the air cleaner.
g01372254 |
Do not use aerosol types of starting aids such as ether. Such use could result in an explosion and personal injury. |
Crush Hazard (9)
This warning is located on all four drum supports.
g01861257 |
Crush Hazard! Machine movement while making adjustments can cause injury or death. Shut off engine and remove key before making adjustments. Refer to the Operation and Maintenance Manual for the proper adjustment procedures. |
Crush Hazard (10)
This warning is located on each side of the front and rear articulation points.
g01371644 |
Stay back a safe distance. No clearance for a person in this area when the machine turns. Severe injury or death from crushing could occur. |