Hook Winch Motor - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1861     | Retaining Ring Pliers     | 1     |
B     | 8H-0663     | Bearing Puller Gp     | 1     |
C     | 1P-1864     | Retaining Ring Pliers As     | 1     |
Start By:
- Remove the hook winch motor. Refer to Disassembly and Assembly, "Hook Winch Motor - Remove".
- Remove check valves (3) .
Show/hide table
Illustration 1 | g01232416 |
- Remove bolts (1) and head (2) .
- Remove O-ring seal (4) and O-ring seal (5) .
Show/hide table
Illustration 2 | g01232417 |
- Remove port plate (6) .
Show/hide table
Illustration 3 | g01233435 |
- Remove bolts (7) and cover (8) .
Show/hide table
Illustration 4 | g01232418 |
Show/hide table
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
- Remove poppet (9), spring (10), piston (11), retainer (12), spring (13), and spring (14) .
Show/hide table
Illustration 5 | g01232419 |
- Remove O-ring seal (16), valve (15), and adjustment screw (17) .
Show/hide table
Illustration 6 | g01232420 |
- Remove O-ring seals (18) .
Show/hide table
Illustration 7 | g01232421 |
- Remove bolts (19) and cover (20) .
Show/hide table
Illustration 8 | g01232422 |
- Remove O-ring seal (21), O-ring seal (22), and bolt (23) .
Show/hide table
Illustration 9 | g01232423 |
- Remove pin (24) and piston (25) .
Show/hide table
Illustration 10 | g01232425 |
- Remove cap (26) .
Show/hide table
Illustration 11 | g01232426 |
Show/hide table
Illustration 12 | g01232428 |
- Use a depth gauge to measure the distance between the end of screw (30) and locknut (29). Record this measurement for assembly purposes.
- Remove locknut (29) and screw (30) .
- Remove plug (27) and the O-ring seal.
- Remove plug (28) and the O-ring seal.
- Remove barrel (31) .
Show/hide table
Illustration 13 | g01233634 |
- Remove O-ring seal (32) from housing (33) .
- Remove spring (34) and shim (35) from barrel (31) .
Show/hide table
Illustration 14 | g01233636 |
- Use Tooling (A) to remove retaining ring (36) .
Show/hide table
Illustration 15 | g01233638 |
- Remove spacer (37) and rotating group (38) .
- Remove seal (39) .
Show/hide table
Illustration 16 | g01233639 |
- Remove bolts (40), pistons (41), center pin (42), and retainer plate (43) .
Show/hide table
Illustration 17 | g01233640 |
- Use Tooling (C) to remove retaining ring (44) .
Show/hide table
Illustration 18 | g01233643 |
- Remove shim (45) .
- Place the rotor assembly in a suitable press. Use Tooling (B) to remove shaft (46) from bearing cone (47), bearing cup (48), shim (49), bearing cup (50), and bearing cone (51) .
Show/hide table
Illustration 19 | g01233644 |
Caterpillar Information System:
416E Backhoe Loader Hydraulic and Steering System Control Valve (Extendable Stick)
583T Pipelayer Machine Systems Hook Winch Motor - Install
583T Pipelayer Machine Systems Hook Winch Motor - Remove
416E Backhoe Loader Hydraulic and Steering System Control Valve (Auxiliary)(Loader)
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler
PM-201 Cold Planer Machine Systems Hydraulic Schematic (Steering System)
Shop Repair Procedure for Positive Pin Retention Track {4169, 4170, 4171, 4174, 4175} Shop Repair Procedure for Positive Pin Retention Track {4169, 4170, 4171, 4174, 4175}
PM-201 Cold Planer Machine Systems Electrical Schematic (Steering System)
2006/01/02 New Guidelines for Inspecting Pistons {1214}
587R Pipelayer Machine Systems Boom Sheave Block (Lower) - Disassemble
R1700G Load Haul Dump Additional Messages
R1700G Load Haul Dump Plate Locations and Film Locations
New Grease Lines for Stick and Boom{7510} New Grease Lines for Stick and Boom{7510}
587R Pipelayer Machine Systems Hook Winch Motor - Assemble
416E Backhoe Loader Hydraulic and Steering System Control Valve (Auxiliary)
PM-201 Cold Planer Machine Systems Water Spray System
416E Backhoe Loader Hydraulic and Steering System Control Valve (Stick)
416E Backhoe Loader Hydraulic and Steering System Control Valve (Bucket)
PM-201 Cold Planer Machine Systems Location of Components (Water Spray System)
330D and 336D Excavators Machine System Specifications Swing Gear and Bearing
587R Pipelayer Machine Systems Boom Sheave Block (Lower) - Assemble
AP-1000D and BG-260D Asphalt Pavers Machine Systems Final Drive Planetary - Remove
PM-201 Cold Planer Machine Systems Electrical Schematic (Water Spray System)
PM-201 Cold Planer Machine Systems Hydraulic Schematic (Water Spray System)