725, 730 and 730 Ejector Articulated Trucks Engine Supplement Caterpillar

Temperature Sensor (Transfer Gear Oil) - Remove and Install

Usage:

725 B1L

Removal Procedure

Show/hide table

NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates.

Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.

Show/hide table




Illustration 1	g01206990

Remove cable strap (1). Remove clip (2) .

Disconnect harness assembly (3) .

Remove temperature sensor (4) .

Remove the O-ring seal from temperature sensor (4) .

Installation Procedure

Note: Cleanliness is an important factor. Before the installation procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.

Show/hide table




Illustration 2	g01206990

Install the O-ring seal onto temperature sensor (4) .

Install temperature sensor (4) .

Connect harness assembly (3) .

Install clip (2). Install cable strap (1) .

Caterpillar Information System:

C3.4B Engines for Caterpillar Built Machines Excessive Engine Oil Consumption - Inspect

311D, 312D, 312D2, 313D, 313D2, 314D, 315D, 318D, 318D2 and 319D Excavators Machine Electronic Control System MID 039 - CID 0190 - FMI 08

2005/10/03 A New Holder Block is Available for the Reclaimer Mixer {6601, 6819}

C6.6 Engines for Caterpillar Built Machines Increased Engine Oil Temperature - Inspect

C7.1 Engines for Caterpillar Built Machines Cooling System - Test

IT62H Integrated Toolcarrier and 950H and 962H Wheel Loaders Machine Systems Tilt Cylinder - Remove and Install

950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System Lift Cylinder

C7.1 Engines for Caterpillar Built Machines Water Temperature Regulator - Test

320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0171 - FMI 04

414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Stabilizer Cylinder

793D Off-Highway Truck Power Train Worksheets

320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0171 - FMI 03

320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0246 - FMI 12

541, 551 and 552 Track Feller Bunchers Machine Systems Tilt Cylinder (Rear for Cab Leveling)

416E, 420E and 430E Backhoe Loaders Hydraulic and Steering System Stabilizer Cylinder

2005/10/03 Responsibilities for Emission Certified Engines {1000}

120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Power Train Introduction

2006/01/02 New Procedures for the Boom Chains {5917, 5917}

320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0247 - FMI 12

966H Wheel Loader and 972H Wheel Loader Power Train MID 081 - CID 2347 - FMI 03

120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Power Train Features

2007/09/17 Improved Idler For Chain Tension Adjuster on Trenchers {4159, 7000}

2005/10/24 Improved Cylinder For Chain Tensioner on Trenchers {671C, 7000}

3516B Off-Highway Trucks Electrical Connectors and Functions