583T Pipelayer Caterpillar


Hook Load Line - Install

Usage:

583T CMX

------ WARNING! ------

在阅读和理解操作和保养手册中的说明和警告之前,请勿操作此机器。 不遵守这些警告,可能会导致人身伤亡。 要更换手册请与卡特彼勒代理商联系。 用户有责任对发动机作适当的关注。


------ WARNING! ------

不要使用扭曲、散开或有磨损点的钢绳。

当搬动钢丝绳时戴上手套。



注意

使用右捻向 9 股钢绳。 钢绳的最小断裂强度应为 26671 kg (58800 lb) 。


表 1
吊钩负载绳技术规格    
动臂高度     缆绳尺寸(直径)     长度    

7315 mm (24 ft)    
19.05 mm(.75 in)    
62.5 m (205 ft)    

8534 mm (28 ft)    
19.05 mm(.75 in)    
86.2 m (283 ft)    

  1. 将动臂降下至水平位置。 把吊钩降到地面上。

    注: 从提升筒上卸下钢绳之前,绞盘筒的提升力必须均衡。

  1. 从吊钩绞盘的提升筒上卸下钢绳。

    参考如有必要,请参阅本手册"绞盘钢绳 - 拆卸和安装"中的信息,以便从绞盘筒上安全地卸下钢绳。

  1. 从提升筒上断开钢绳的固定器。

  1. 从滑轮组上卸下钢绳。


    注意

    从缠绕轴上放开钢绳。 决不要将钢绳成卷提离缠绕轴。


  1. 从滑阀上展开新的钢绳。

    注: 在钢绳两端焊接,以避免钢绳磨损。

  1. 将钢绳的金属环安装在提升筒上。



    图 1g01166909

  1. 将一半的钢绳均匀地缠绕在提升筒上。



    图 2g00624622

  1. 将绞盘筒上的吊钩负载绳 (9) 安装在滑轮组上。 将钢绳放在上滑轮 (1) 上,下滑轮 (4) 下,上滑轮 (2) 上,下滑轮 (5) 下,上滑轮 (3) 上,下滑轮 (6) 下。

    注: 吊钩负载绳应从朝向机器前面的上滑轮 (1) 上穿过。 将钢绳朝向机器后部固定。

  1. 将钢绳插入凹口,缠在楔块 (7) 上。

  1. 将钢绳端穿过卡箍 (8) 。 将固定螺钉拧入卡箍中,拧紧至扭矩 45 ± 7 N·m (33 ± 5 lb ft)。

  1. 将吊钩操纵杆移到提升(缓慢)位置。 将操纵杆保持在此位置,直到钢绳收紧。 将下滑轮组抬离地面,然后抬高动臂。

Caterpillar Information System:

950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Braking and Hydraulic Fan System General Information (Brake, Hydraulic Fan System)
AP-1055D and BG-2455D Asphalt Pavers Propel System Harness (Speed Potentiometer) and Electronic Sensor - Test
C9 Engine for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
587R Pipelayer Hook and Wire Cable - Inspect
PS-150B and PS-200B Paving Compactors Daily Inspection
C27 and C32 Engines for Caterpillar Built Machines Injector Solenoid Circuit - Test
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Conveyor System
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Location of Hydraulic Components
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Location of Electrical Components
793D Off-Highway Truck Suction Screen (Rear Axle Lubrication) - Clean
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Introduction
793D Off-Highway Truck/Tractor Relay Valve (Brake) - Install
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Piston Pump (Conveyor) - Auger Conveyor and Drag Conveyor
12M, 140M and 160M Motor Graders Hydraulic and Steering System Hydraulic System Pressure - Test and Adjust
AccuGrade® Laser (CB420) Bank Valve (Grade Control)
785D OEM Off-Highway Truck Fuel Tank Water and Sediment - Drain
TH580B Telehandler Hydraulic System Boom Hydraulic System
793C Off-Highway Truck Fuel System Primary Filter - Clean - If Equipped
793D Off-Highway Truck/Tractor Fuel Tank - Remove
793D Off-Highway Truck/Tractor Fuel Tank - Install
AP-1055D and BG-2455D Asphalt Pavers Conveyor Systems Piston Motor (Conveyor) - Auger Conveyor and Drag Conveyor
C9 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
966H and 972H Wheel Loaders Braking and Hydraulic Fan System Brake Accumulator
120M, 12M, 140M and 160M Motor Graders Machine Systems Switch (Window Wiper)
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.