PM-201 Cold Planer Caterpillar


Engine Starting

Usage:

PM-201 PNM



图 1g01139963

  1. 将安全链锁在操作平台上。

  1. 将推进操纵杆 (3) 向后拉至 NEUTRAL(空档)位置。

  1. 接合驻车制动器。 按下旋钮 (2) 。



    图 2g01171742

  1. 将转筒开关 (4) 移至 OFF 位置。

    注: 操作者面板中的所有 ON 和 OFF 开关都应处于 OFF 位置。

  1. 将转向模式开关 (1) 移至 MANUAL REAR STEER(手动后转向)位置。



    图 3g01139964

  1. 拔出七个远程停机开关 (5) 。 这是远程停机开关的 RESET(复位)位置。

  1. 将节气门开关 (7) 移至低怠速位置。 这可获得低怠速。

  1. 鸣响喇叭 (8) 几秒。 这会警告附近的人员。

  1. 将发动机起动开关 (6) 转至 ON。 让监控系统面板进行自我检查。 如果显示出任何故障,进行必要的修正。

  1. 将发动机起动开关 (6) 转至 START。 当发动机起动后你应该松开发动机起动钥匙。 如果显示出任何故障,进行必要的修正。

    注: 在飞轮停止转动以前不要再次接合起动马达。

  1. 让发动机在低怠速运转至少五分钟,以便暖机。


注意

发动机盘车时间不要超过30秒钟。 再次盘车之前让起动机冷却2分钟。

在发动机油的指示灯或仪表指明机油压力已经足够之前,在低的机油压力下运转发动机,如果不用低速,就会损坏涡轮增压器。

发动机的钥匙必须保持在运转位置,以保持电力供应,维持液压功能及防止机器严重损坏。

如果发动机不能起动,先把钥匙转回到断开 位置,才可恢复 起动。


如果温度低于 −18 °C (0 °F),使用寒冷天气起动辅助装置。 可以使用下列寒冷天气起动辅助装置:

  • 冷却液加热器

  • 燃油加热器

  • 水套水加热器

  • 额外的蓄电池容量

Caterpillar Information System:

834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 0353 - FMI 08
PM-201 Cold Planer Service Light Power Receptacle
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Operator Platform - Install
834H Wheel Dozer and 836H Landfill Compactor Machine Systems Operator Platform - Remove
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 0353 - FMI 01
C15 and C18 Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
2005/01/31 Improved Lifters are Now Used {1102, 1121, 1123}
2005/01/31 Improved Lifters are Now Used {1102, 1121, 1123}
PM-201 Cold Planer Plate Locations and Film Locations
PM-201 Cold Planer Capacities (Refill)
PM-201 Cold Planer Lubricant Viscosities
C15 and C18 Engines for Caterpillar Built Machines Coolant Level Sensor Circuit - Test
PM-201 Cold Planer Engine and Machine Warm-Up
PM-201 Cold Planer Machine Interlocks
PM-201 Cold Planer Hood Tilt
PM-201 Cold Planer Service Support (Leg Lock)
PM-201 Cold Planer Servicing the Rotor
R2900G Load Haul Dump Collet Pin Bolt Torque - Check
C11 and C15 Engines for Caterpillar Built Machines Throttle Position Sensor Circuit - Test
C15 and C18 Engines for Caterpillar Built Machines Engine Shutdown Switch Circuit - Test
793D Off-Highway Truck Battery Disconnect Switch
AP-1055D and BG-2455D Asphalt Pavers Machine Systems Piston Pump (Right Drag Conveyor and Left Auger Conveyor) - Remove
539 Knuckleboom Loader Cooling System Coolant Level - Check
RM-300 Soil Stabilizer Safety Messages
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.