Engine Oil Pump - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
B     | 1P-0510     | 起子总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g01053962 |
- 利用工具 (B) 将套筒轴承 (11) 装入泵体中。 轴承接头应距两个轴承孔中心线 30 ± 15 度。 安装套筒轴承,使套筒轴承与泵体的外侧齐平。
- 最终组装前,检查机油泵所有零件的状态和技术规格。 请参阅技术规格, "机油泵"。
- 使用清洁的发动机机油润滑惰齿轮和驱动齿轮。 使用清洁的发动机机油润滑套筒轴承 (11) 。 将惰齿轮 (5) 和驱动齿轮 (4) 安装到泵体 (3) 中。
Show/hide table
图 2 | g01043546 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装盖 (10) 。 通过安装螺栓 (12) 将盖固定到泵体上。
注: 在组装后发动机机油泵必须能转动自如。 用手转动发动机机油泵。 如果发动机机油泵不能转动自如,重新安置盖 (10) 。
- 安装安全阀柱塞 (7) 、弹簧 (8) 、护圈 (9) 和螺栓 (6) 。
- 将键安装在轴上。
- 将驱动齿轮 (1) 安装到机油泵 (2) 的轴上。 安装螺栓 (13) 。 拧紧螺栓至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 3 | g01043619 |
End By: 安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C15 On-Highway Engine Engine Oil Pump - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Install
3524B Engines for 797 and 797B Off-Highway Trucks Cold Mode Operation
CP-323C and CS-323C Paving Compactors Circuit Breakers - Reset
CP-323C and CS-323C Paving Compactors Battery or Battery Cable - Inspect/Replace
C15 and C18 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
CP-323C and CS-323C Paving Compactors Battery - Clean/Check
CAES ULTRA Machine Control ; Guidance Products Computer Aided Earthmoving System Digital Terrain Model
CAES ULTRA Machine Control ; Guidance Products Computer Aided Earthmoving System Switches
CAES ULTRA Machine Control ; Guidance Products Computer Aided Earthmoving System Annunciator
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Hydraulic Oil Cooler - Remove and Install
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Hydraulic Tank - Remove and Install
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarrier Hydraulic System Relief Valve (Line) - Test and Adjust
2004/03/29 Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
CP-323C and CS-323C Paving Compactors Cooling System Coolant (ELC) - Change
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Remove
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Disassemble
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Assemble
CB-214D, CB-224D and CB-225D Vibratory Compactors Machine Systems Gear Pump (Steering) - Install
2004/02/16 Lighting Group Uses New Seals and Bolt-On Covers {1429, 1434}
C15 and C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
446D Backhoe Loader Engine Crankcase Breather - Clean
2004/02/16 Correction to Testing and Adjusting , "Piston Pump Neutral - Test and Adjust" {5070}
446D Backhoe Loader Engine Air Precleaner - Clean