Alternator - Remove and Install
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Turn the battery disconnect switch to the OFF position.
- Remove the alternator belt. Refer to Operation and Maintenance Manual for the correct procedure.
Show/hide table
Illustration 1 | g01020040 |
- Remove wire assemblies (1) and clip (2) from alternator (8) .
- Remove bolt (4A) (not shown) from belt guard (5) .
- Remove bolt (6) from guard (7) .
- Remove guard (7) .
- Loosen nut (4) and position bracket (3) out of the way.
- Remove bolt (9) .
- Remove alternator (8) .
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install alternator (8) .
Show/hide table
Illustration 2 | g01020040 |
- Install bolt (9) .
- Position bracket (3) to the original location and tighten nut (4) .
- Install guard (7) .
- Install bolt (6) on guard (7) .
- Install belt guard (5) and bolt (4A) (not shown).
- Install wire assemblies (1) and clip (2) on alternator (8) .
- Install the alternator belt. Refer to Operation and Maintenance Manual for the correct procedure.
- Turn the battery disconnect switch to the ON position.
Caterpillar Information System:
Load Haul Dump Power Train Cab Mounting
12H Motor Grader Engine Supplement Electric Starting Motor - Remove and Install
777D and 777D HAA Off-Highway Truck and 776D Off-Highway Tractor Operation Information
248B and 268B Skid Steer Loaders Machine Systems Control Valve (Work Tool)
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Main Control Valve - Assemble
777D and 777D HAA Off-Highway Truck and 776D Off-Highway Tractor Operation Information
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Hydraulic System Oil Sample - Obtain
248B and 268B Skid Steer Loaders Machine Systems Control Valve (Work Tool)
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Main Control Valve - Disassemble
12H Motor Grader Engine Supplement Air Compressor - Remove and Install
572R Series II Pipelayer Hydraulic System Counterweight Relief Valve - Test and Adjust
826G Series II Landfill Compactor, 825G Series II Soil Compactor and 824G Series II Wheel Dozer Transmission Oil Sample - Obtain
R2900G Load Haul Dump Steering System Steering System (High Pressure Oil Circuit)
R2900G Load Haul Dump Steering System Steering System Troubleshooting
12H Motor Grader Engine Supplement Turbocharger - Remove and Install
12H Motor Grader Engine Supplement Refrigerant Compressor - Remove and Install
572R Series II Pipelayer Power Train Transmission
267B, 277B and 287B Multi Terrain Loaders Machine Systems Radiator and Hydraulic Oil Cooler
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Final Drive - Install
12H Motor Grader Engine Supplement Unit Injector Hydraulic Pump - Remove and Install
572R Series II Pipelayer Bevel and Transfer Gears
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Install
572R Series II Pipelayer Power Train Drive Shaft
TH220B and TH330B Telehandlers Machine Systems Control Valve (Trailer and Towing Hitch) - Install