Pistons and Connecting Rods - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-3601     | 活塞环扩展器     | 1     |
B     | 1P-1861     | 挡圈钳     | 1     |
C     | 5P-8639     | 液压 (连杆轴承)     | 1     |
8F-0024 | 软管组件     | 1     | |
1P-2375 | 快速连接连接器     | 1     | |
1P-2376 | 快速连接连接器     | 1     | |
4C-9751 | 隔套     | 1     | |
4C-9749 | 衬套接头     | 1     | |
4C-9750 | 衬套接头     | 1     | |
9U-6600 | 手动液压泵     | 1     |
注: 从发动机上拆下之前,活塞和连杆组件上已经作了标记。 所有的部件必须重新组装起来。 所有部件必须安装回它们在发动机中原来的位置。 请勿互换任何部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (C) 拆掉旧轴承,同时安装新轴承 (6) 。 工具 (C) 的适配器应与连杆 (3) 的表面充分接触。
注: 将轴承接头两端方位 (X) 正确调整在 12 ± 5 度范围内。
- 沿长度 (Y) 加热连杆 (3) 。
(Y) 加热连杆的最大长度 ... 75 ± 5 mm (3.0 ± 0.2 in)
Show/hide table注意 在安装活塞销子轴承的时候,必须对连杆进行加热处理。 不要使用明火加热。
- 让连杆和轴承冷却到室温。
- 沿长度 (Y) 加热连杆 (3) 。
Show/hide table
图 1 | g01126305 |
Show/hide table
图 2 | g01126306 |
- 用下列程序安装活塞环 (4) 。
- 将控油环的弹簧安置在活塞体组件中的油环槽中。
- 将控油环安置在弹簧的上方。 安置控油环,使其开口与弹簧接头成 180 度。 使用工具 (A) 将控油环安装在活塞上。
- 使用工具 (A) 安装中间活塞环,使有 "UP-2" 标记的一侧朝向活塞顶部。
- 使用工具 (A) 安装顶部活塞环,使有 "UP-1" 标记的一侧朝向活塞顶部。
- 安置活塞环 (4) ,使端隙彼此相隔 120 度。
Show/hide table
图 3 | g01126141 |
- 检查活塞环 (4) 的端隙。 请参阅技术规格, "活塞和活塞环"。
- 将活塞 (1) 放置在连杆 (3) 上。 将清洁的发动机机油涂抹在活塞销 (5) 上,并安装活塞销。 使用工具 (B) 安装挡圈 (2) 。 确保挡圈完全就位在活塞组件的环槽中。
End By: 安装活塞和连杆。 请参阅 拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
AP-655C Asphalt Paver Access Doors and Covers
AP-655C Asphalt Paver Roading the Machine
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
Supplemental Documentation for the Payload Control System{7494} Supplemental Documentation for the Payload Control System{7494}
797 Off-Highway Truck Braking System Oil Cooler (Brake, Hydraulic Fan, Steering)
797 Off-Highway Truck Braking System Oil Cooler (Rear Brake)
AP-655C and BG-2255C Asphalt Pavers Operation Information
267, 277 and 287 Multi Terrain Loaders Machine Systems Bogie Wheel
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Transmission - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Install
Rework Procedure for the Tube Assembly of the Yoke{7050, 7051} Rework Procedure for the Tube Assembly of the Yoke{7050, 7051}
R2900G Load Haul Dump Machine Electrical System Engine Stop
C7 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
CAESbasic Installation {7604} CAESbasic Installation {7604}
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove
C7 Engines for Caterpillar Built Machines Unit Injector Sleeve - Install
R2900G Load Haul Dump Machine Electrical System Engine Shutdown
R2900G Load Haul Dump Machine Electrical System Engine Monitoring
R2900G Load Haul Dump Machine Electrical System Actual Gear Indicator
Field Installation of the 234-0777 Quick Coupler Conversion Ar {6129} Field Installation of the 234-0777 Quick Coupler Conversion Ar {6129}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070} Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
RM-350B Road Reclaimer/Soil Stabilizer Machine Systems Mixing Chamber - Install