Brake Proportional Manifold (Traction Control System) - Assemble
Assembly Procedure
- Check the condition of all seals and of all valve components. If any parts are worn or damaged, use new parts for replacement. Apply clean hydraulic oil to any moving parts.
- Install plugs (13), plug (14) and fitting (15) on manifold (1). The torque for plugs (13) is 20 ± 5 N·m (15 ± 4 lb ft). The torque for plugs (14) is 3.0 ± 0.5 N·m (27 ± 4 lb in). The torque for fitting (15) is 20 ± 5 N·m (15 ± 4 lb ft).
Show/hide table
Illustration 1 | g00282851 |
Note: The plugs on the manifold are of three different sizes.
- Install the rings and O-ring seals (12) on cartridge assembly (11) .
Show/hide table
Illustration 2 | g00282850 |
- Install cartridge assembly (11) on manifold (1). The torque for cartridge assembly (11) is 25 ± 5 N·m (18 ± 4 lb ft).
Show/hide table
Illustration 3 | g00282848 |
- Install coil assembly (9) and nut (10) on manifold (1). The torque for nut (10) is 3.0 ± 0.5 N·m (27 ± 4 lb in).
Show/hide table
Illustration 4 | g00282846 |
- Install the rings and O-ring seals (8) on valves (7) .
Show/hide table
Illustration 5 | g00282845 |
- Install valves (7) on manifold (1). The torque for valves (7) is 25 ± 5 N·m (18 ± 4 lb ft).
Show/hide table
Illustration 6 | g00282843 |
- Install O-ring seals (6) on cartridge assemblies (5) .
Show/hide table
Illustration 7 | g00282842 |
- Install cartridge assemblies (5) on manifold (1). The torque for cartridge assemblies (5) is 20 ± 5 N·m (15 ± 4 lb ft).
Show/hide table
Illustration 8 | g00282840 |
- Install the following items on manifold (1) : coil assemblies (4), spacers (3) and nuts (2). The torque for nuts (2) is 9.5 ± 1.5 N·m (7.0 ± 1.1 lb ft).
Show/hide table
Illustration 9 | g00282839 |
Show/hide table
Illustration 10 | g00282838 |
End By: Install the proportional brake valve. Refer to Disassembly and Assembly, "Brake Valve (Proportional) (Traction Control System) - Install".
Caterpillar Information System:
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Disassemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Proportional Manifold (Traction Control System) - Remove
C7 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Brake Control Valve (Service) - Remove and Install
120H and 135H Motor Graders Engine Power Loss
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Metering Pump (HMU) - Remove
120H and 135H Motor Graders Engine Overheating
R2900G Load Haul Dump Machine Electrical System Engine Start
TH62, TH63, TH82 and TH83 Telehandlers Lifting Capacities
CB-434D Paving Compactor Steering Frame Lock
CB-434D Paving Compactor Towing the Machine
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Transmission - Install
267, 277 and 287 Multi Terrain Loaders Machine Systems Bogie Wheel
AP-655C and BG-2255C Asphalt Pavers Operation Information
797 Off-Highway Truck Braking System Oil Cooler (Rear Brake)
797 Off-Highway Truck Braking System Oil Cooler (Brake, Hydraulic Fan, Steering)
Supplemental Documentation for the Payload Control System{7494} Supplemental Documentation for the Payload Control System{7494}
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
AP-655C Asphalt Paver Roading the Machine
AP-655C Asphalt Paver Access Doors and Covers
C7 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
Rework Procedure for the Tube Assembly of the Yoke{7050, 7051} Rework Procedure for the Tube Assembly of the Yoke{7050, 7051}
R2900G Load Haul Dump Machine Electrical System Engine Stop