208-1018 Drive and Steering Axle Gp, without Steering Sensor
Illustration 1 | g00944835 |
(1) Torque of the locknut for the steering stop ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(1A) Torque of the locknut for the steering stop (not shown) ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(2) Install the breather so that the slot in the breather is parallel with the axle half shaft.
Note: Apply Loctite 638 sealant to the threads prior to installing the breather.
(3) Torque for locknut ... 250 N·m (185 lb ft)
(4) Torque for the ball joint ... 300 N·m (220 lb ft)
(5) Torque for three bolts ... 190 N·m (140 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the plugs.
(6) Torque for the plug ... 60 N·m (45 lb ft)
(7) Torque for four plugs (two plugs in each carrier assembly) ... 25 N·m (20 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plugs.
(8) Torque for plug ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plug.
(9) Torque for 11 bolts ... 169 N·m (125 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(10) Torque for two plugs (one plug in each carrier assembly) ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plugs.
189-5717 Drive and Steering Axle Gp, with Steering Sensor
Illustration 2 | g00944836 |
(1) Torque for four bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(2) Torque of the locknut for the steering stop ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(2A) Torque of the locknut for the steering stop (not shown) ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(3) Torque for breather ... 10 N·m (90 lb in)
Install the breather so that the slot in the breather is parallel with the axle half shaft.
Note: Apply Loctite 638 sealant to the threads prior to installing the breather.
(4) Torque for three bolts ... 190 N·m (140 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the bolts.
(5) Torque for tie rod nut ... 250 N·m (185 lb ft)
(6) Torque for four kingpin bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(7) Torque for locknut ... 250 N·m (185 lb ft)
(8) Torque for the ball joint ... 300 N·m (220 lb ft)
(9) Torque for the plug ... 60 N·m (45 lb ft)
(10) Torque for the plug ... 60 N·m (45 lb ft)
(11) Torque for 10 bolts ... 169 N·m (125 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installation of the bolts.
(12) Torque for plug (each carrier assembly) ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plugs.
208-1020 Drive and Steering Axle Gp, without Steering Sensor
Illustration 3 | g00944834 |
(1) Torque for four bolts ... 300 N·m (220 lb ft)
(2) Torque of the locknut for the steering stop ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(2A) Torque of the locknut for the steering stop (not shown) ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(3) Torque for breather ... 10 N·m (90 lb in)
Install the breather so that the slot in the breather is parallel with the axle half shaft.
Note: Apply Loctite 638 sealant to the threads prior to installing the breather.
(4) Torque for three bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(5) Torque for tie rod nut ... 280 N·m (205 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the nut.
(6) Torque for four kingpin bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(7) Torque for locknut ... 350 N·m (260 lb ft)
(8) Torque for the ball joint ... 550 N·m (405 lb ft)
(9) Torque for the plug ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plugs.
(10) Torque for plug ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plug.
(11) Torque for thirteen axle housing bolts ... 169 N·m (125 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(12) Torque for plug (each carrier assembly) ... 25 N·m (20 lb ft)
(13) Torque for plug (each carrier assembly) ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plugs.
168-7443 Drive and Steering Axle Gp, with Steering Sensor
Illustration 4 | g00944837 |
(1) Torque for four bolts ... 300 N·m (220 lb ft)
(2) Torque of the locknut for the steering stop ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(2A) Torque of the locknut for the steering stop (not shown) ... 150 N·m (110 lb ft)
Note: Apply Loctite 270 sealant to the threads prior to installing the breather.
(3) Torque for breather ... 10 N·m (90 lb in)
Install the breather so that the slot in the breather is parallel with the axle half shaft.
Note: Apply Loctite 638 sealant to the threads prior to installing the breather.
(4) Torque for three bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(5) Torque for tie rod nut ... 280 N·m (205 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the nut.
(6) Torque for four kingpin bolts ... 300 N·m (220 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(7) Torque for locknut ... 350 N·m (260 lb ft)
(8) Torque for the ball joint ... 550 N·m (405 lb ft)
(9) Torque for the plug ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plugs.
(10) Torque for thirteen axle housing bolts ... 169 N·m (125 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the bolts.
(11) Torque for plug (each carrier assembly) ... 25 N·m (20 lb ft)
(12) Torque for plug (each carrier assembly) ... 60 N·m (45 lb ft)
Note: Apply Loctite 638 sealant to the threads prior to installing the plugs.