Axle - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 6V-3145 | Load Leveling Beam | 1 |
| 1U-8226 | Lifting Sling | 2 | |
| ZZ | 6V-9507 | Face Seal Plug (9/16 - 18 THD) | 1 |
| 6V-9828 | Cap As (9/16 - 18 THD) | 1 | |
Start By:
- Remove the final drive planetary (axle propel). Refer to Disassembly and Assembly, "Final Drive Planetary (Axle Propel) - Remove".
- Remove both of the wheels and tires. Refer to Disassembly and Assembly, "Wheel and Tire - Remove and Install".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- If the axle is equipped with brakes, disconnect fitting (2) from axle (1) .
Show/hide table
 | |
| Illustration 1 | g00984959 |
- Attach Tooling (A) and a suitable lifting device to each end of axle (1), as shown.
Show/hide table
 | |
| Illustration 2 | g00942148 |
Show/hide table
 | |
| Illustration 3 | g00942151 |
- Remove bolts (3) from both sides of axle (1) .
Show/hide table
 | |
| Illustration 4 | g00984964 |
- Lower axle (1) and remove the axle from the rear of the machine. The weight of the axle is approximately 470 kg (1036 lb).
Caterpillar Information System:
8-16B Asphalt Screed Gerotor Motor (Vibratory)
C15 Petroleum Generator Set Engines Cylinder Head Valves
2002/12/02 Correction to Testing and Adjusting , "Service Brake Control (Pedal) - Adjust" {4269, 4269}
8-16B Asphalt Screed Power Adjuster Motor (Crown)
TH340B, TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Joystick Control - Remove and Install
TH210 and TH215 Telehandlers Machine Systems Cab - Remove
R1300G Load Haul Dump Braking System Brake Release Cylinder
2002/12/23 Correction to Systems Operation Testing and Adjusting "Ride Control Accumulator Testing and Charging (If Equipped)" {5077}
R1300G Load Haul Dump Braking System Solenoid Valve (Parking Brake)
R1300G Load Haul Dump Braking System Brake Control Valve (Parking)
R1300G Load Haul Dump Braking System Pressure Reducing Valve (Parking Brake Oil)
2002/12/23 Correction to Systems Operation Testing and Adjusting "Ride Control Accumulator - Test and Charge" {5077}
R1600G Load Haul Dump Ride Control - If Equipped
8-16B Asphalt Screed Power Adjuster Motor (Height)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Paving Compactors Machine Systems Axle - Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Paving Compactors Machine Systems Articulating and Oscillating Hitch - Remove
8-16B Asphalt Screed Solenoid Valve (Extender)
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Paving Compactors Machine Systems Articulating and Oscillating Hitch - Install
CS56B, CP56B, CS66B, CS68B and CP68B Vibratory Soil Compactors Machine Systems Wheel and Tire - Remove and Install
8-16B Asphalt Screed Glow Plugs
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Paving Compactors Machine Systems Propel Control (Direction, Speed) - Remove
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Paving Compactors Machine Systems Propel Control (Direction, Speed) - Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Paving Compactors Machine Systems Control Cable (Direction, Speed) - Remove and Install
CP-563E, CP-573E, CS-563E, CS-573E and CS-583E Paving Compactors Machine Systems Control Valve (Shift) - Remove