G3516C and G3516E Gas Engines Caterpillar

Camshaft Bearing Position

Usage:

G3516C F6D

Show/hide table




Illustration 1	g03043756
Right side view

Show/hide table

Table 1
Specification for 219-4711 Cylinder Block Gp and 370-9890 Cylinder Block Gp
Item	Qty	Part	Specification Description
The camshaft bearings from the rear surface of the cylinder block are the following dimensions:
The oil holes must be aligned at the correct angle when the bearings are installed. Refer to Specifications, "Cylinder Block" for the correct angle.
A	-	-	Distance is 2200.0 ± 1.5 mm (86.61 ± 0.06 inch).
B	-	-	Distance is 1930.0 ± 1.5 mm (75.98 ± 0.06 inch).
C	-	-	Distance is 1660.0 ± 1.5 mm (65.35 ± 0.06 inch).
D	-	-	Distance is 1390.0 ± 1.5 mm (54.72 ± 0.06 inch).
E	-	-	Distance is 1120.0 ± 1.5 mm (44.09 ± 0.06 inch).
F	-	-	Distance is 850.0 ± 1.5 mm (33.46 ± 0.06 inch).
G	-	-	Distance is 580.0 ± 1.5 mm (22.83 ± 0.06 inch).
H	-	-	Distance is 310.0 ± 1.5 mm (12.20 ± 0.06 inch).
K	-	-	Distance is 40.0 ± 1.5 mm (1.57 ± 0.06 inch).

Caterpillar Information System:

C18 Marine Engines Turbocharger - Remove and Install

C18 Marine Engines Electronic Unit Injector Sleeve - Remove and Install

3516B Engine for the MT4400D Off-Highway Truck Fuel Injector

C18 Marine Engines Electronic Unit Injector - Remove and Install

G3516C and G3516E Gas Engines Cylinder Block

G3516C and G3516E Gas Engines Cylinder Block

G3500B Engines Crankshaft

3516B Engine for the MT4400D Off-Highway Truck Turbocharger

2013/08/21 A New High-Temperature Tee Hose Is Available for Crankcase Breathers on 3500, G3500, 3600, G3600, and C280 Engines {1317}

2012/09/27 A New High-Temperature Tee Hose Is Available for Crankcase Breathers on 3500 Machine Engines {1317}

301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Lubricant Viscosities

UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Bearing (Earlier) - Replace

C18 Marine Engines Inlet and Exhaust Valve Springs - Remove and Install

C18 Marine Engines Inlet and Exhaust Valves - Remove and Install

2012/05/21 Viewing the Electronic Thermostat Position via ET on C175 Engines {135V, 7610}

C18 Marine Engines Inlet and Exhaust Valve Guides - Remove and Install

C18 Marine Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install

2012/05/21 New Clamping for the Jacket Water Bypass Tube on Certain 3500 Engines {1380, 7553}

3512C and 3516C Marine Propulsion Engines Speed Control - Test

G3500 Generator Sets Fluid Recommendations

2012/05/23 Activation Password Is Now Required For Touchscreens Of Uninterruptible Power Supplies {7451}

G3512E Generator Set Engines Engine Oil Pan

C7.1 Industrial Engine Product Description - Engine and Aftertreatment

G3516C and G3516E Gas Engines Water Pump