430E Backhoe Loader Caterpillar

Specifications

Illustration 1	g01621120

(1) 111-4343 Pin

Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)

Bore for the pin ... 40.130 ± 0.025 mm (1.5799 ± 0.0010 inch)

Note: As required, use the following washer in order to provide a maximum clearance of 1.0 ± 0.5 mm (0.04 ± 0.02 inch):

(2) 119-4594 Washer

Quantity ... 8

Thickness of one washer ... 1.0 mm (0.04 inch)

(3) 122-4954 Pin As

Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)

Bore for the pin assembly ... 40.130 ± 0.025 mm (1.5799 ± 0.0010 inch)

Illustration 2	g01621151
(4) Tilt cylinder (5) Link (7) Lift cylinder

(6) 130-5451 Pin

Pin diameter ... 44.95 ± 45.00 mm (1.770 ± 1.772 inch)

Bore for pin in the sleeve bearing after installation ... 45.213 ± 0.058 mm (1.7800 ± 0.0023 inch)

Illustration 3	g01622272

(8) 111-4342 Pin

Pin diameter ... 44.95 to 45.00 mm (1.770 to 1.772 inch)

Bore for the pin ... 45.130 ± 0.025 mm (1.7768 ± 0.0010 inch)

Note: After assembly of the sleeve bearings, coat all the bores and sleeve bearings with 5P-0960 Grease Cartridge after cleaning and before painting.

(9) 9R-6690 Sleeve Bearing

Quantity ... 4

Inside diameter ... 60.315 ± 0.020 mm (2.3746 ± 0.0008 inch)

Outside diameter ... 73.111 ± 0.013 mm (2.8784 ± 0.0005 inch)

(10) As required, use the following spacers in order to provide a maximum clearance of 1.0 mm (0.0394 inch). Position the spacers in order to equalize the clearance within 3 mm (0.1 inch) between the wear bars on the lift arms and the wear bars on the radiator guard for each side of the machine.

128-7903 Spacer

Quantity ... 2

Thickness of one spacer ... 3 mm (0.1 inch)

128-7905 Spacer

Quantity ... 2

Thickness of one spacer ... 1.0 mm (0.0394 inch)

(11) 111-4340 Pin

Pin diameter ... 59.950 to 60.000 mm (2.3602 to 2.3622 inch)

Bore diameter for pin in the sleeve bearing after installation ... 60.237 ± 0.046 mm (2.3715 ± 0.0018 inch)

Note: As required, use the following washer in order to provide a maximum total clearance of 1.0 mm (0.04 inch).

(12) 9R-8390 Spacer

Quantity ... 2

Thickness of one spacer ... 1.0 mm (0.04 inch)

Note: As required, use the following washer in order to provide the maximum clearance of 1.0 ± 0.5 mm (0.04 ± 0.02 inch).

(13) 111-4337 Washer

Quantity ... 14

Thickness of one washer ... 1.0 mm (0.04 inch)

(14) 9R-0411 Sleeve Bearing

Quantity ... 4

Inside diameter ... 45.295 ± 0.020 mm (1.7833 ± 0.0008 inch)

Outside diameter ... 58.082 ± 0.013 mm (2.2867 ± 0.0005 inch)

(15) 111-4334 Pin

Pin diameter ... 44.95 to 45.00 mm (1.7697 to 1.7717 inch)

Bore for the pin in the sleeve bearing after installation ... 45.238 ± 0.046 mm (1.7810 ± 0.0018 inch)

(16) 116-4825 Sleeve Bearing

Quantity ... 4

Inside diameter ... 45.198 ± 0.020 mm (1.7794 ± 0.0008 inch)

Outside diameter ... 58.584 ± 0.013 mm (2.3065 ± 0.0005 inch)

(17) 111-4341 Pin

Pin diameter ... 44.95 to 45.00 mm (1.7697 to 1.7717 inch)

Bore for the pin in the sleeve bearing after installation ... 45.139 ± 0.046 mm (1.7771 ± 0.0018 inch)

(18) As required, use the following washer in order to provide the maximum clearance of 1.0 ± 0.5 mm (0.04 ± 0.02 inch):

119-4594 Washer

Quantity ... 6

Thickness of one washer ... 1.0 mm (0.04 inch)

(19) 114-3836 Pin

Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)

Bore for the pin ... 40.225 ± 0.025 mm (1.5837 ± 0.0010 inch)

Illustration 4	g01622358

(20) 111-4343 Pin

Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)

Bore for the pin in the sleeve bearing after installation ... 40.135 ± 0.046 mm (1.5801 ± 0.0018 inch)

(21) 116-4825 Sleeve Bearing

Quantity ... 2

Inside diameter ... 45.198 ± 0.020 mm (1.7794 ± 0.0008 inch)

Outside diameter ... 58.584 ± 0.013 mm (2.3065 ± 0.0005 inch)

Illustration 5	g01622377
Section J-J

(22) 9R-1496 Sleeve Bearing

Quantity ... 2

Inside diameter ... 40.196 ± 0.020 mm (1.5825 ± 0.0008 inch)

Outside diameter ... 53.576 ± 0.013 mm (2.1093 ± 0.0005 inch)

(23) 125-1037 Pin As

Pin diameter ... 44.95 ± 45.00 mm (1.7697 ± 1.7717 inch)

Bore for the pin in the sleeve bearing after installation ... 45.139 ± 0.046 mm (1.7771 ± 0.0018 inch)

Loader Arrangement

Linkage Assembly

Removal Procedure

Show/hide table



Illustration 6	g01625920

1. Remove retaining rings (1) . Remove plate (2) . Remove retaining rings (4) . Remove link assembly (5) . Remove plate (3) .

2. Repeat for opposite side of the loader.

Installation Procedure

1. Install link assembly (5) in the reverse order of removal.

   1. Install shims as required, to obtain a maximum total clearance of 1.0 ± 0.5 N·m (9 ± 4 lb in).

Loader Arrangement

Removal Procedure

1. Remove the tilt cylinders.

2. Remove the quick coupler.

Show/hide table



Illustration 7	g00759798

3. Place Tooling (A) under the rear of the machine, as shown.

Show/hide table



Illustration 8	g01626470

4. Install Tooling (B) under the loader frame.

Show/hide table



Illustration 9	g01626474

5. Remove pin (5) and the washers. Note the location of washers in order to aid in installation. Lower lift cylinder (7) . Disconnect harness assembly (1) .

6. Disconnect hose assembly (6) . Repeat for the other side.

7. Remove link assembly (2) . Attach a suitable lifting device to loader assembly (3) . The weight of loader assembly (3) is approximately 408 kg (900 lb). Remove pin (4) . Remove loader assembly (3) .

Installation Procedure

1. Install loader assembly (3) in the reverse order of removal.

   1. Refer to Loader Arrangement Specifications section for the correct shimming procedure.