Engine Oil Pump
Show/hide table
图 1 | g02555999 |
Show/hide table
技术规格 - 244-8985 发动机机油泵总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
在安装泵之前,先用清洁的发动机机油润滑运动的零件。 用手旋转泵以确认泵能够旋转自如。 | |||
1 | 1 | 298-6387 O 形密封圈 | 在装配前,用 5P-3975 橡胶润滑剂稍微润滑孔。 |
Show/hide table
图 2 | g02556002 |
Show/hide table
技术规格 - 244-8985 发动机机油泵总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
2 | 1 | 2S-2760 弹簧 | 测试力下的长度为 测试力为 测试后的自由长度约为 |
Show/hide table
图 3 | g02556004 |
剖面 A-A |
Show/hide table
技术规格 - 244-8985 发动机机油泵总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
C | 1 | 7N-5052 齿轮 | 长度为 机油泵体中新齿轮孔的深度为 |
D | 1 | 7W-1017 轴 | 直径为 装配后, 7W-0060 衬套上的新轴组件孔径为 |
E | 2 | 4M-3248 空心定位销 | 自机油泵盖上的延伸长度为 |
F | - | - | 自惰轮轴末端至齿轮端面的距离为 |
G | 1 | 7N-5058 泵驱动轴 | 直径为 装配后, 7W-0060 衬套上的新轴组件孔径为 |
H | - | - | 自轴末端至齿轮端面的距离为 |
J | 1 | 7W-0050 泵盖 | 泵盖上 7W-0060 衬套的安装深度为 |
K | 1 | 4P-5637 机油泵体组件 | 机油泵体组件上的 7W-0060 衬套安装深度为 |
Show/hide table
图 4 | g02556006 |
Show/hide table
技术规格 - 244-8985 发动机机油泵总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
L | 2 | 7N-2043 定位销 | 自机油泵盖上的延伸长度为 |
Show/hide table
图 5 | g02556007 |
Show/hide table
技术规格 - 244-8985 发动机机油泵总成 | |||
项目 | 数量 | 零件 | 技术规格说明 |
M | - | - | 从中线穿过轴承孔的 7W-0060 衬套接头位置为 45 ± 15 度。 |
- | - | - | 工作台测试技术参数:
700 rpm 时的不受限流速为 300 rpm 下出口全闭时的泵压力为 |
Caterpillar Information System:
3500 Engines Air Inlet and Exhaust Lines
G3520B Industrial Engines Timing Offset - Calibration
G3520B Industrial Engines Fuel Shutoff - Test
3500 Engines Exhaust Manifold
G3520B Engines Gear Group (Front)
G3520B Industrial Engines Ignition Transformer
Salvage of Center Bearing in Torque Converter Input Housing {3101, 3127} Salvage of Center Bearing in Torque Converter Input Housing {3101, 3127}
G3520B Industrial Engines General Information (Electronic Control System)
345D, 349D and 349D2 Excavators Hydraulic System Boom Hydraulic System
C18 Marine Engines Configuration Parameters
3512C and 3516C Industrial Engines Turbocharger
C11 and C13 Engines Turbocharger
3176C, 3406E and 3456 Industrial Engines Speed Control - Test
Reuse and Salvage for C-280 & 3600 Engine Cylinder Blocks {1201} Reuse and Salvage for C-280 & 3600 Engine Cylinder Blocks {1201}
330D, 336D, 336D2, 340D and 340D2 Excavators Machine System Specifications Seat Belt
793F and 793F XQ Off-Highway Truck Fast Fill Service System Limit Switch (Grease Low Level)
793F and 793F XQ Off-Highway Truck Fast Fill Service System Visual Inspection
2008/09/01 An Improved Front Mounted Open Crankcase Ventilation System Is Now Used {1074, 1317}
Instructions for the Field Installation of a Secondary Crankcase Breather Kit on the C15 On-highway Engines{1317, 1317} Instructions for the Field Installation of a Secondary Crankcase Breather Kit on the C15 On-highway Engines{1317, 1317}
2008/03/01 A New Purge Pump and Service Pack are Now Used {107P}
Installation Procedure for the Fuel Transfer Kit on the Hydraulic Electronic Unit Injector (HEUI) Pump{1256} Installation Procedure for the Fuel Transfer Kit on the Hydraulic Electronic Unit Injector (HEUI) Pump{1256}
793F and 793F XQ Off-Highway Truck Hydraulic Fan and Steering System Liquid Level Switch (Steering Tank)
345D, 349D and 349D2 Excavators Hydraulic System Control Valve (Boom Lowering) - If equipped
C4.4 Industrial Engine Fuel Filter