Wheel and Tire (Rear) - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 425-0952 | Chock | 2 |
B | 504-9790 | Lift Gp (60Hz)(1) | 2 |
OR | |||
504-9792 | Lift Gp (50Hz)(2) | 2 |
Show/hide table
(1) | High-Voltage (480V) Low-Voltage (240V) |
(2) | High-Voltage (400V) Low-Voltage (200V) |
Start By:
- Connect the steering frame lock.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to chock the front wheels.
Show/hide table
Illustration 2 g06271348 Typical Example - Position Tooling (B) as shown in Illustration 2 to raise the rear of the machine until the rear wheels are off the ground. Refer to Tool Operating Manual, NEHS1303, "Lift Group (Stand - 25 Ton)" for more information on Tooling (B).
Show/hide table
Illustration 3 g01349205 - Attach a suitable lifting device onto rear wheel (1). Remove bolts (2). Remove rear wheel (1) from the spindle hub. The weight of rear wheel (1) is approximately
215 kg (475 lb) . Repeat this step for the remaining wheels.
Show/hide table
Illustration 1 | g01349206 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 425-0952 | Chock | 2 |
B | 504-9790 | Lift Gp (60Hz)(1) | 2 |
OR | |||
504-9792 | Lift Gp (50Hz)(2) | 2 |
Show/hide table
(1) | High-Voltage (480V) Low-Voltage (240V) |
(2) | High-Voltage (400V) Low-Voltage (200V) |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use a suitable lifting device to install rear wheel (1). The weight of rear wheel (1) is approximately
215 kg (475 lb) . Install bolts (2). Tighten bolts (2) to a torque of900 ± 100 N·m (664 ± 74 lb ft) . Repeat this step for the remaining wheels.Show/hide tableIllustration 5 g06271348 Typical Example - Use Tooling (B) to lower the rear of the machine. Remove Tooling (B).
Show/hide table
Illustration 6 g01349206 - Remove Tooling (A) from the front wheels.
Show/hide table
Illustration 4 | g01349205 |
End By:
- Separate the steering frame lock.
Caterpillar Information System:
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Seat - Assemble
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Seat - Disassemble
CP76 and CS76 Vibratory Compactors Machine Systems Hydraulic Schematic (Vibratory System)
770 and 772 Off-Highway Truck/Tractors Front Suspension (Cylinder) - Assemble
770 and 772 Off-Highway Truck/Tractors Front Suspension (Cylinder) - Disassemble
770 and 772 Off-Highway Truck/Tractors Front Suspension (Cylinder) - Install
770 and 772 Off-Highway Truck/Tractors Front Suspension (Cylinder) - Remove
CP76 and CS76 Vibratory Compactors Machine Systems Electrical Schematic (Vibratory System)
CP76 and CS76 Vibratory Compactors Machine Systems Eccentric Weight
120M and 12M Motor Graders Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
826K Landfill Compactor Fire Suppression System - Check - If Equipped
CP76 and CS76 Vibratory Compactors Machine Systems Piston Motor (Vibratory)
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Eccentric Weight Housing Group
CP54 and CS54 Vibratory Soil Compactors Propel System Pressure Override Valve (Drum Propel Pump) - Test and Adjust
CP56, CS56, CP64, CS64, CP74 and CS74 Vibratory Soil Compactors Machine Systems Eccentric Weight Housing Group
14L Motor Grader Machine Systems Front Frame from Rear Frame (Articulating Hitch) - Separate
CP56B, CP68B, CS56B and CS68B Vibratory Soil Compactors Machine Systems Hydraulic Cylinder (Leveling Blade)
938H Wheel Loader and IT38H Integrated Toolcarrier Power Train Electronic Control Module
2007/10/08 Test Lines Are No Longer Used {1359, 4250, 4300, 4324, 5050, 5070, 5117}
12M and 120M Motor Graders Power Train Transmission Oil Cooler - Remove
CP54 and CS54 Vibratory Soil Compactors Propel System Pressure Override Valve (Axle Propel Pump) - Test and Adjust
12M and 120M Motor Graders Power Train Transmission Oil Cooler - Install
Procedure to Install the New Pinion Shaft and Circle Worm Drive in the Circle Drive{5207} Procedure to Install the New Pinion Shaft and Circle Worm Drive in the Circle Drive{5207}
CP76 and CS76 Vibratory Compactors Machine Systems Hydraulic Schematic (Hydraulic Fan)