UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Caterpillar

Graphical User Interface Messages

Usage:

Show/hide table

Table 1
Event Type
Code	Type	Color
A	Alarm	Red
N	Notice	Yellow
L	Log	Green

Show/hide table

Table 2
UPS Status
Code	Status
A	AVR
B	Bypass
D	Discharge
NC	No Change
S	Shutdown
O	Online

Note: The UPS will remain online as long as there are enough functioning flywheels to support the load. Therefore, any notice or alarm from a flywheel may not result in a UPS state change.

Show/hide table

Table 3
Message	Event Type	UPS Status	Description
Email send failure		NC	(Ethernet Option Only) The UI attempted to send an email but there was problem communicating with the email server.
Email Sent Successfully	L	NC	(Ethernet Option Only) The UI successfully sent an email to the email server.
Invalid Password entered at UI	L	NC	An invalid password was entered from the front panel.
Invalid Password Entered from View	L	NC	An invalid password was entered from a UPSView connection.
Modem Callback: Connected.	L	NC	A UPSView (laptop) connection was established via modem.
Modem Callback: Connection Error	L	NC	A UPSView (laptop) connection was attempted via modem.
Page send failure		NC	The UPS attempted to dial a pager but the paging service did not answer.
Paging Cancelled	L	NC	The paging activity was canceled via UPSView or the display of the UI.
Paging Initiated	L	NC	The UPS is attempting to dial a pager.
Remote Ethernet Access Disabled	L	NC	A non-serial UPSView connection cannot issue control commands to the UPS. This access was removed either by the operator through the front panel (UI display) or the remote access has timed-out.
Remote Ethernet Access Enabled	L	NC	A non-serial UPSView connection can issue control commands to the UPS. This access was granted by the operator through the front panel. (UI display)
Remote Modem Access Disabled	L	NC	A non-serial UPSView connection cannot issue control commands to the UPS. This access was removed either by the operator through the front panel (UI display) or the remote access has timed-out.
Remote Modem Access Enabled	L	NC	A non-serial UPSView connection can issue control commands to the UPS. This access was granted by the operator through the front panel. (UI display)
Resetting User Interface	L	NC	A command was issued to reboot the UI.
SNMP Trap Test Event		NC	(SNMP Option) A test trap was issued.
UI Connected: _	L	NC	A UPSView (laptop) connection was established. (serial, Ethernet, or modem)
UI Disconnected: _	L	NC	A UPSView (laptop) connection was removed. (serial, Ethernet, or modem)
UI Email Test Event.	L	NC	(Ethernet Option Only) A user level email test was initiated.
UI Factory Email Test Event.	L	NC	(Ethernet Option Only) A service level email test was initiated.
UI Master User Password entered	L	NC	A "master user level" password was entered through the display of the UI
UI Master User Password reset	N	NC	A "master user level" password was reset to the default password.
UI Mfg/Engr Password entered	L	NC	A "manufacturing/engineering level" password was entered through the display of the UI.
UI Pager Test Event: pager: "<PAGER NUMBER>"	L	NC	A test page was sent via modem.
UI Password Cleared	L	NC	A password that was entered through the display has been cleared and is no longer active.
UI Password Expired	L	NC	A password that was entered through the display has timed-out and is no longer active.
UI Service Password entered	L	NC	A "service level" password was entered through the display of the UI.
UI User Password entered	L	NC	A "user level" password was entered through the display of the UI.
View Master User Password entered	L	NC	A "master user level" password was entered through UPSView.
View Mfg/Engr Password entered	L	NC	A "manufacturing/engineering level" password was entered through UPSView. View
Password Cleared	L	NC	A password that was entered through UPSView has been cleared and is no longer active.
View Password Expired	L	NC	A password that was entered through UPSView has timed-out and is no longer active.
View Service Password entered	L	NC	A "service level" password was entered through UPSView.
View User Password entered	L	NC	A "user level" password was entered through UPSView.