F341 Transmission Speed Sensor - Failed Low
Show/hide table
Illustration 1 | g00562250 |
(1) Chassis Control Module. (2) Speed Sensor (Transmission). (3) Speed Sensor (Engine). |
This fault code indicates the transmission speed sensor has a lower than normal voltage and may be due to a shorted sensor or a harness short to chassis ground.
- Inspect transmission speed sensor connector (C162) to determine whether the sensor, connectors or Rear Main harness is damaged.
Expected Result: There is damaged parts or broken parts.
- YES, repair as appropriate and recheck fault codes. If fault code is not active, repair is complete.
- NO, go to Step 2.
- YES, repair as appropriate and recheck fault codes. If fault code is not active, repair is complete.
- Disconnect transmission speed sensor and measure the resistance across terminals A and B. The resistance should be 2550 ohms.
Expected Result: There is a short in the circuit.
- YES, replace transmission speed sensor. Check fault code and if no longer active the repair is complete.
- NO, go to Step 3.
- YES, replace transmission speed sensor. Check fault code and if no longer active the repair is complete.
- If engine RPM sensor is functioning properly, exchange the transmission speed and engine RPM sensors. Check fault codes.
Expected Result: The fault code is not active.
- YES, install new transmission speed sensor. Check fault code and if no longer active the repair is complete.
- NO, go to Step 4.
- YES, install new transmission speed sensor. Check fault code and if no longer active the repair is complete.
- Disconnect Chassis Control Module connector C002. Check for short circuit between C162-1 and C162-B.
Expected Result: There is a short in the circuit.
- YES, locate and repair short circuit in Rear Main harness. Check fault code and if no longer active the repair is complete.
- NO, go to Step 5.
- YES, locate and repair short circuit in Rear Main harness. Check fault code and if no longer active the repair is complete.
- Check for short circuit from chassis ground to C162-1 and C162-2.
Expected Result: There is a short in the circuit.
- YES, locate and repair short circuit in Rear Main harness. Check fault code and if no longer active the repair is complete.
- NO, go to Step 6.
- YES, locate and repair short circuit in Rear Main harness. Check fault code and if no longer active the repair is complete.
- Download latest control module software into all control modules.
Expected Result: There is a short in the circuit.
- YES, go to Step 7.
- NO, repair is complete. Calibrate transmission and three-point hitch.
- YES, go to Step 7.
- Replace the Chassis Control Module (CCM).
Expected Result: There is a short in the circuit.
- YES, install the original CCM and repeat this troubleshooting procedure.
- NO, go to Step 8.
- YES, install the original CCM and repeat this troubleshooting procedure.
- Install the original CCM.
Expected Result: There is a short in the circuit.
- YES, original CCM was faulty. Replace original CCM with new CCM. If fault code is not active, repair is complete. Download latest control module software into all modules. Calibrate transmission and three-point hitch.
- NO, this fault code may have been caused by faulty connectors. Keep the original on the tractor. Clean all terminals on the CCM and reconnect. If fault code is not active, repair is complete. Download latest control module software into all modules. Calibrate transmission and three-point hitch.
- YES, original CCM was faulty. Replace original CCM with new CCM. If fault code is not active, repair is complete. Download latest control module software into all modules. Calibrate transmission and three-point hitch.
Caterpillar Information System:
CB-534C and CB-634C Vibratory Compactors Vibratory System Visual Inspection
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Oil Step Speed Calibration
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F340 Transmission Speed Sensor - Failed High
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Diagnostic Operation
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F339 CCM Sensor 5 Volt Supply - Failed High
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F338 CCM Sensor 5 Volt Supply - Failed Low
AP-1000B and BG-260C Asphalt Pavers Parking Brake Control
3524B Engine for Caterpillar Built Machines Accessory Drive (Rear) - Remove
554 Forwarder and 574 Forwarder Cab Tilt Hydraulic System Oil Level - Check
D400E Series II Articulated Truck Accumulator (Suspension) - Remove and Install
773D and 775D Quarry Trucks and 773E and 775E Off-Highway Trucks Power Train Transfer Gears - Assemble
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Accessory Drive (Front) - Install
797 Off-Highway Truck Power Train Gear Pump (Transmission Charging and Scavenge)
554 Forwarder and 574 Forwarder Cab Door Hinges - Lubricate
D400E Series II Articulated Truck Hoist Control Valve - Remove
554 Forwarder and 574 Forwarder Gate Cylinders - Lubricate
3524B Engine for Caterpillar Built Machines Accessory Drive (Rear) - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Service Operations
Challenger 65C, Challenger 65D, Challenger 65E, Challenger 70C, Challenger 75C, Challenger 75D, Challenger 75E, Challenger 85C, Challenger 85D, Challenger 85E and Challenger 95E Agricultural Tractors Machine Monitor System Relays
Digital Voltage Regulator Instantaneous Trip Shutdown - Troubleshoot
AP-1000B and BG-260C Asphalt Pavers Manual Propel Override Control
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Magnetic Pickup Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Diode Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Engine Oil Pressure Switch Test