Accessory Drive (Rear) - Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 422-7508 | 密封件安装工具 | 1 |
B | 8T-5096 | 千分表总成 | 1 |
C | 5L-9018 | 螺栓 | 1 |
1P-0488 | 驱动板 | 1 | |
1P-0493 | 驱动板 | 1 | |
1P-0531 | 手柄 | 1 | |
D | - | Loctite 航空垫片密封胶 | - |
E | - | Henkel 51102 镍防咬合剂 | - |
- 检查后部附件驱动装置的所有 O 形密封圈和部件有无磨损或损坏。 如有必要,更换后部附件驱动装置的部件。
- 安装前,用清洁的发动机机油润滑 O 形密封圈。
- 安装前,确保后部附件驱动装置的所有部件清洁且无异物。
Show/hide table
图 1 g03325763 Show/hide table图 2 g03325429 - 使用工具 (C) 将套筒轴承 (22) 安装到轴承保持架 (19) 中。 将套筒轴承上的孔与轴承保持架 (19) 上的孔 (X) 对准。
- 将止推垫圈 (21)和定位销 (20) 安装到轴承保持架 (19) 上。
Show/hide table
图 3 g03325176 Show/hide table图 4 g03325175 - 将保持架组件 (19 )放置到飞轮壳 (13) 中。
- 将螺栓 (17)、垫圈和支架安装到壳体 (13) 上以固定保持架组件 (19)。
Show/hide table
图 5 g03325173 - 将齿轮 (15) 放置在飞轮壳 ( 13 )内,以便于安装。
Show/hide table
图 6 g03325589 - 安装轴 (16)。
Show/hide table
表 2 螺栓 (14) 的扭矩表 附件驱动装置总成 扭矩技术规格 137-8335 280 ± 40 N·m (207 ± 30 lb ft) 9Y-1595、 7N-3978、 8N-8161 和 121-5710 90 ± 15 N·m (66 ± 11 lb ft) - 安装螺栓 (14),将轴 (16) 固定至齿轮。 有关螺栓 (14) 的正确扭矩技术规格,请参阅表 2。
Show/hide table
图 7 g03206300 Show/hide table图 8 g03325574 - 用螺栓 (11) 和垫圈将板 (12) 和密封垫安装至飞轮壳 (13)。
Show/hide table
图 9 g03325887 Show/hide table图 10 g03325375 - 使用工具 (C) 将轴承 (10) 安装到适配器 (4) 中。 将轴承 (10) 上的孔与适配器 (4) 上的孔 (Y) 对准。
Show/hide table
图 11 g03325169 - 将 O 形密封圈 (7)、止推垫圈 (6)和定位销 (5) 安装到适配器 (4) 上。
Show/hide table
图 12 g03326390 - 如果拆下了双头螺柱,请参阅表 2,了解双头螺柱的正确扭矩技术规格。 将工具 (D) 涂抹在螺柱螺纹上。 安装适配器 (4)、垫圈和螺母 (3)。 有关螺母 (3) 的正确扭矩技术规格,请参阅表 2。
Show/hide table
表 3 螺母 (3) 和双头螺柱的扭矩表(如有必要) 附件驱动装置总成 螺母 (3) 的扭矩技术规格 双头螺柱的扭矩技术规格 137-8335、 9Y-1595 和 7N-3978 标准扭矩 110 ± 15 N·m (81 ± 11lb ft) 8N-8161 220 ± 25 N·m (162 ± 18 lb ft) 100 ± 15 N·m (74 ± 11 lb ft) 121-5710 标准扭矩 115 ± 15 N·m (85 ± 11 lb ft) Show/hide table图 13 g03326408 Show/hide table图 14 g03177145 Show/hide table图 15 g03326411 - 将唇形密封 (9) 放置到工具 (A) 上并手动开始进行安装。 密封件开始座入适配器 (4) 时,允许挤出塑料安装套筒。 报废塑料安装套筒。
- 如果需要,请使用软铜锤或适当工具。 密封件安装到到合适深度时,工具 (A) 将停在适配器面上。 唇形密封 (9) 刚好与适配器面下部齐平。
Show/hide table
图 16 g03326413 Show/hide table图 17 g03204977 - 手动将防尘密封件 (8) 均匀安装到位。 图 17 显示正确安装的密封件。
注: 唇形密封在适配器中保持静止不动时,防尘密封件随轴一起转动。
Show/hide table图 18 g03326416 注: 安装前,确保锁紧螺母 (1) 和垫圈的轴承表面无润滑脂。
注: 安装轭前,确保轭锥面 (2) 和轴无油脂。
- 将轭 (2) 安装到轴上。 将工具 (E) 涂抹到锁紧螺母 (1) 的螺纹上。 安装垫圈和锁紧螺母 (1)。 有关锁紧螺母 (1) 的正确扭矩技术规格,请参阅表 2。
Show/hide table
表 4 锁紧螺母 (1) 的扭矩表 附件驱动装置总成 锁紧螺母 (1) 的扭矩技术规格 137-8335、 875 ± 50 N·m (645 ± 37 lb ft) 121-5710和 9Y-1595 750 ± 50 N·m (553 ± 37 lb ft) 7N-3978 650 ± 50 N·m (480 ± 37 lb ft) - 使用工具 (B) 和适当的撬杆确保轴端隙正确。 轴的轴向间隙测量值应为
0.15 mm to 0.77 mm (0.006 inch to 0.031 inch) 。
Caterpillar Information System:
554 Forwarder and 574 Forwarder Gate Cylinders - Lubricate
D400E Series II Articulated Truck Hoist Control Valve - Remove
554 Forwarder and 574 Forwarder Cab Door Hinges - Lubricate
797 Off-Highway Truck Power Train Gear Pump (Transmission Charging and Scavenge)
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F341 Transmission Speed Sensor - Failed Low
CB-534C and CB-634C Vibratory Compactors Vibratory System Visual Inspection
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Oil Step Speed Calibration
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F340 Transmission Speed Sensor - Failed High
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Diagnostic Operation
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F339 CCM Sensor 5 Volt Supply - Failed High
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F338 CCM Sensor 5 Volt Supply - Failed Low
AP-1000B and BG-260C Asphalt Pavers Parking Brake Control
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Service Operations
Challenger 65C, Challenger 65D, Challenger 65E, Challenger 70C, Challenger 75C, Challenger 75D, Challenger 75E, Challenger 85C, Challenger 85D, Challenger 85E and Challenger 95E Agricultural Tractors Machine Monitor System Relays
Digital Voltage Regulator Instantaneous Trip Shutdown - Troubleshoot
AP-1000B and BG-260C Asphalt Pavers Manual Propel Override Control
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Magnetic Pickup Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Diode Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Engine Oil Pressure Switch Test
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems Mode 1 - Operator Calibrations
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Crankshaft Front Seal - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F342 Engine RPM Sensor - Failed High
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines Slave Relay Test
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Electronic Systems F343 Engine RPM Sensor - Failed Low