Flywheel - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
Always wear protective gloves when handling parts that have been heated. |
- Use an oven and heat ring gear (2) to a maximum temperature of 150 °C (302 °F). Install the ring gear.
- Position the ring gear (4) on flywheel (2) .
Show/hide table
Illustration 1 | g00562859 |
- Check the condition of the dowels (not shown). If the dowels are damaged, use new parts for replacement.
Show/hide table
Illustration 2 | g00527024 |
- Install Tool (A), a strap, and a suitable lifting device onto flywheel (2) .
- Install flywheel (2). The weight of the flywheel is 50 kg (110 lb).
Note: Dowel pin hole (3) is slightly offset in order to ensure correct installation.
- Install six bolts (1) in order to secure flywheel (2) onto the crankshaft. Tighten the bolts to a torque of 83 ± 5 N·m (61 ± 4 lb ft).
- Remove Tool (A) .
- Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for more information on flywheel runout.
Caterpillar Information System:
320B Excavator Machine System Specifications Stick - 6280 mm (247.2 inch)
M312, M315, M318 and M320 Excavators Hydraulic System Pump Control (Main Hydraulic)
317B Excavator Machine System and Attachment Specifications Boom -
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System Harness Code Mode
3064 and 3066 Engines for Caterpillar Built Machines Cylinder Head - 3064
320B Excavator Machine System Specifications Lines (Stick Cylinder)
317B Excavator Machine System and Attachment Specifications Lines (Stick Cylinder)
M312, M315, M318 and M320 Excavators Hydraulic System Main Hydraulic Pump
M312, M315, M318 and M320 Excavators Hydraulic System Pump Hydraulic System
317B Excavator Machine System and Attachment Specifications Lines (Stick Cylinder)
5110B Excavator, 24H Motor Grader, 69D, 769D, 773D, 773E, 776D and 777D Off-Highway Truck/Tractors, 771D, 775D and 775E Quarry Trucks and AD40 Series II, AD45 and AE40 II Underground Articulated Trucks Caterpillar Monitoring System System Schematic
3408E and 3412E Engines for Caterpillar Built Machines Fuel System
3064 and 3066 Engines for Caterpillar Built Machines Gear Group (Front)
317B Excavator Machine System and Attachment Specifications Stick Lines
307B Excavator Machine Systems Swivel - Disassemble
307B Excavator Machine Systems Swivel - Assemble
3064 and 3066 Engines for Caterpillar Built Machines Camshaft
3046 Engine For Caterpillar Built Machines Crankshaft Rear Seal - Remove
307B Excavator Machine Systems Swing Motor - Remove
307B Excavator Machine Systems Swing Motor - Install
3046 Engine For Caterpillar Built Machines Crankshaft Rear Seal - Install
317B Excavator Machine System and Attachment Specifications Stick Lines - Short
3046 Engine For Caterpillar Built Machines Flywheel Housing - Remove and Install
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Clamshell