Engine Oil Pan - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 7M-7260 | 液体垫片 | 1 |
| B | - | 3/8 - 16 NC 导向螺栓 | 4 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查机油泵接头的 O 形密封圈 (4) 。 如果密封件被切削、刮伤或有裂痕，则安装一个新的密封件。 用清洁的发动机机油润滑密封件孔。 安装密封件。
Show/hide table
 | |
| 图 1 | g00604494 |
典型示例 | |
- 确保密封垫 (3) 表面清洁。 将工具 (A) 涂抹到密封垫 (3) 上。 在油底壳中安装工具 (B) 。 将密封垫就位。
- 将适当起吊设备连在发动机吊耳上。
- 3508 发动机的重量约为 4445 kg (9800 lb)。 油底壳的重量约为 240 kg (530 lb)。
- 3512 发动机的重量约为 5900 kg (13,000 lb)。 油底壳的重量约为 295 kg (650 lb)。
- 3516 发动机的重量约为 7711 kg (17,000 lb)。 油底壳的重量约为 409 kg (900 lb)。
- 3508 发动机的重量约为 4445 kg (9800 lb)。 油底壳的重量约为 240 kg (530 lb)。
Show/hide table
 |
不适当的吊具会使被吊装设备翻倒，造成伤害和损坏。 |
注: 如果使用了不适当的设备来起吊发动机，可能发生人身伤害和设备损坏。 使用合适额定承重力的钢索或链条。 使用平压机并根据发动机起吊贴膜上的信息连接钢索或链条。
Show/hide table
 | |
| 图 2 | g00604420 |
典型示例 | |
- 提升发动机。 将发动机置于油底壳上或将油底壳置于发动机下面。 从油底壳上拆下工具 (B) 。
- 安装螺栓 (2) 以将发动机和油底壳固定在一起。
Show/hide table
 | |
| 图 3 | g00604419 |
典型示例 | |
Show/hide table
 | |
| 图 4 | g00604418 |
典型示例 | |
- 安装螺栓 (1) 以将机油泵的接头固定在油底壳上。
Show/hide table
 | |
| 图 5 | g00604417 |
典型示例 | |
- 用机油加注发动机曲轴箱。 参考操作和保养手册, "容量（加注）"，了解机油容量。
Caterpillar Information System:
D250E Series II and D300E Series II Articulated Trucks Power Train Solenoid and Relief Valve (Output Transfer Gears)
D350E Series II and D400E Series II Articulated Trucks Power Train Solenoid and Relief Valve (Output Transfer Gears)
R2900 Load Haul Dump Automatic Lubrication Inline Filter - Clean - Hydraulic Type - If Equipped
C9 Engines for Caterpillar Built Machines Engine Design
R2900 Load Haul Dump Automatic Lubrication Filler Filter - Clean - Hydraulic Type - If Equipped
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Pan - Assemble
RM-500 Road Reclaimer/Soil Stabilizer Machine Systems Rotor Drive Planetary - Disassemble
R2900 Load Haul Dump Automatic Lubrication Grease Tank - Fill - Hydraulic Type - If Equipped
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Pan - Disassemble
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Pan - Remove
3524B Engine for Caterpillar Built Machines Engine Oil and Water Pump Drive - Install
2002/09/16 Air Fuel Ratio Control Valve Diaphragm Available for Service on Lucas Fuel Injection Pumps {1278}
TH220B, TH330B, TH340B, TH350B, TH355B, TH360B, TH460B, TH560B and TH580B Telehandlers Power Train Hydraulic Schematic (Power Train System)
TK711, TK721, TK722 and TK732 Track Feller Bunchers Access Door and Cover Locations
120H and 135H Motor Graders Machine Systems Bank Valve - Assemble - Bank Valve with Hydraulic Detent
CB-534D and CB-564D Asphalt Compactors Offset Cylinder Ends - Lubricate - If Equipped
R2900 Load Haul Dump Backup Alarm - Test
TK711, TK721, TK722 and TK732 Track Feller Bunchers Lubricant Viscosities
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Turbocharger
3508 and 3516 EUI Engines and 5130 and 5230 Excavators Radiator
TK711, TK721, TK722 and TK732 Track Feller Bunchers Capacities (Refill)
TK711, TK721, TK722 and TK732 Track Feller Bunchers Air Conditioner/Cab Heater Filter (Recirculation) - Inspect/Replace
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Remove
3524B Engine for Caterpillar Built Machines Engine Oil Scavenge Pump - Disassemble