Flywheel - Remove
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | Guide Studs1/2 × 4 × 20 threads per inch | 2 | |
B | 138-7575 | Link Bracket | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (1).
Show/hide table
Illustration 2 g00905929 - Install Tooling (A).
Show/hide table
Illustration 3 g00905930 - Install Tooling (B).
- Remove remaining bolts (1) that secure flywheel (2) to the crankshaft.
- Use Tooling (B) and a suitable lifting device in order to remove flywheel (2) and ring gear (3) from the housing. The weight of the flywheel is approximately
54 kg (120 lb) .Show/hide tableIllustration 4 g00906037 - Check the condition of the ring gear (3). Replace the ring gear with a new part if the gear is worn or damaged.
Note: Identify the orientation of the ring gear on the flywheel for the correct positioning when the new ring gear is installed.
- Place flywheel (2) and ring gear (3) on a suitable support.
- Use a hammer and a punch in order to remove ring gear (3) from the flywheel.
Show/hide table
Illustration 1 | g00905926 |
Caterpillar Information System:
2002/07/22 Correction to Operation and Maintenance Manual , "Engine Oil and Filter - Change" {1318}
2002/07/22 Correction to Operation and Maintenance Manual , "Engine Oil and Filter (CF-4 Multigrade) - Change - 3516B Standard Displacement Engine Only" {1318}
D5N Track-Type Tractor Power Train Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
3406E and C15 Marine Engines Turbocharger - Inspect
CP-533C, CS-533C, CP-563C, CS-563C, CS-573C and CS-583C Vibratory Compactors Steering System Gear Pump (Charge, Steering, Offset and Wheel Tilt)
CB-434C Vibratory Compactor Fuel System - Prime
Flexxaire Fan Hydraulic Actuated Fan - Disassemble
D5N Track-Type Tractor Power Train Pressure Charts
R1700G Load Haul Dump Implement and Steering Lockout (Wheel Steering) - Test
R1700G Load Haul Dump Implement and Steering Lockout (STIC Steering) - Test
R1700G Load Haul Dump Hydraulic Tank Breaker Relief Valve - Clean
2002/07/22 Correction to Operation and Maintenance Manual , "Engine Oil and Filter (CF-4 Multigrade) - Change" {1318}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Hydraulic System Relief Valve
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System Hydraulic Tank and Filter
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Timing - Check
2002/07/22 Correction to Operation and Maintenance Manual , "Lubricant Specifications" {1000, 1300, 7000, 7581}
143H and 163H Motor Graders All Wheel Drive Location of Hydraulic Components
Flexxaire Fan Hydraulic Actuated Fan - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Steering System Piston Pump (Steering)
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Braking and Hydraulic Fan System Hydraulic Oil Contamination - Test
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders Engine Temperature Sensor Open or Short Circuit - Test
TH210 and TH215 Telehandlers Engine Supplement Alternator - Remove and Install
TH210 and TH215 Telehandlers Engine Supplement Electric Starting Motor - Remove and Install
140H and 160H Motor Graders Additional Messages