Alternator - Remove and Install
Removal Procedure
Start By:
- Disconnect the battery. Refer to Disassembly and Assembly, "Battery and Battery Cable - Seperate and Connect".
- Disconnect harness assembly (1). Disconnect harness assembly (2) .
Show/hide table
Illustration 1 | g00887750 |
- Remove bolts (3). Remove bolts (6). Remove cover (5). Loosen bolts (7) and (8). Remove belt (4). Remove bolts (7) and (8). Remove alternator (9) .
Show/hide table
Illustration 2 | g00887732 |
Installation Procedure
- Place alternator (9) in position.
Show/hide table
Illustration 3 | g00887732 |
- Install bolts (7) and (8). Do not tighten bolts (7) and (8) at this time.
Note: When you install the alternator, ensure that the alternator pulley is in alignment with the crankshaft pulley within 2.4 mm (0.09 inch).
- Install belt (4). Refer to the Operation and Maintenance Manual, SEBU7468, "Belts - Inspect/Adjust/Replace" for the correct procedure.
- Torque bolt (7) to 15 ± 3 N·m (11 ± 2 lb ft).
- Torque bolt (8) to 30 ± 7 N·m (22 ± 5 lb ft).
- Place cover (5) in position.
- Torque washers and bolts (6) to 15 ± 3 N·m (11 ± 2 lb ft).
- Install washers and bolts (3) to a torque of 6 ± 1 N·m (53 ± 9 lb in).
- Connect harness assembly (2). Connect harness assembly (1). Torque the nut to 8 ± 2 N·m (71 ± 18 lb in).
Show/hide table
Illustration 4 | g00887750 |
End By: Connect the battery. Refer to Disassembly and Assembly, "Battery and Battery Cable - Seperate and Connect".
Caterpillar Information System:
216 and 232 Skid Steer Loaders 3024 Engine Supplement Battery and Battery Cable - Separate and Connect
216, 226, 232 and 242 Skid Steer Loaders Machine Systems Hydraulic System Pressure - Release
Air Conditioning and Heating R-12 All Caterpillar Machines Refrigerant Accumulator
Air Conditioning and Heating R-12 All Caterpillar Machines Receiver-Dryer
RM-350B Reclaimer/Mixer All Wheel Drive Electronic Control System Sensors
RM-350B Reclaimer/Mixer All Wheel Drive Electronic Control System Solenoid Valves
Replacement Instructions for the P2 Pressure Switch on D350E and D400E Articulated Trucks{1435} Replacement Instructions for the P2 Pressure Switch on D350E and D400E Articulated Trucks{1435}
RM-350B Reclaimer/Mixer All Wheel Drive Electronic Control System Relays
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power Train Transmission Oil Cooler
RM-350B Reclaimer/Mixer All Wheel Drive Electronic Control System Switches
793C XQ Off-Highway Truck Fan Drive Tank Oil - Change
216, 226, 232 and 242 Skid Steer Loaders Machine Systems Tire and Rim
226 and 242 Skid Steer LoadersEngine Supplement Electric Starting Motor - Remove and Install
247 and 257 Multi Terrain Loaders3034 Engine Supplement Water Temperature Regulator - Remove and Install
247 and 257 Multi Terrain Loaders3034 Engine Supplement Water Pump - Remove and Install
226 and 242 Skid Steer LoadersEngine Supplement Gear Motor (Fan) - Remove
247 and 257 Multi Terrain Loaders3034 Engine Supplement Radiator and Hydraulic Oil Cooler - Remove
Air Conditioning and Heating R-12 All Caterpillar Machines Heating and Air Conditioning Control System
247 and 257 Multi Terrain Loaders3034 Engine Supplement Radiator and Hydraulic Oil Cooler - Install
226 and 242 Skid Steer LoadersEngine Supplement Air Cleaner - Remove and Install
226 and 242 Skid Steer LoadersEngine Supplement Muffler - Remove and Install
216 and 232 Skid Steer Loaders 3024 Engine Supplement Engine Enclosure - Remove and Install
RM-350B Road Reclaimer/Mixer Power Train Control Valve (Rear Propel/Freewheel)
Air Conditioning and Heating R-12 All Caterpillar Machines Heating System Schematic