Parameter Descriptions
Injector Codes
Note: The injector codes are not part of the "Configuration" screen on Cat ET. "Injector Codes Calibration" can be found under "Calibrations" in the "Service" menu on Cat ET.
The injector code is a number that is found on each of the unit injectors. The ECM uses this number to compensate for manufacturing variations between individual injectors. If you replace any of the unit injectors, you must reprogram the code for the new injectors. Also, if you replace the ECM, you must reprogram all of the injector codes.
"Product ID"
The "Product ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 8 characters can be entered in the field.
"Equipment ID"
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 17 characters can be entered in the field.
"Engine Serial Number"
The "Engine Serial Number" should be programmed to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed on a replacement ECM.
"FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information ratings plate. This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required.
"FTS" (Full Torque Setting)
"FTS" is similar to "FLS". This value should only be changed if the engine is rerated or a new ECM is installed. Factory passwords are required.
"Throttle Lock Engine Speed Limit"
The "Throttle Lock Engine Speed Limit" parameter allows the maximum engine speed (rpm) for the throttle lock to be programmed within the available range.
"Ether Control"
The "Ether Control" parameter allows the operation of this feature to be enabled or disabled.
"System Battery Voltage Low Elevated Idle"
The "System Battery Voltage Low Elevated Idle" parameter allows the operation of this feature to be enabled or disabled. Refer to Troubleshooting, "Elevated Idle" for more information.
"Engine Fan Control"
The "Engine Fan Control" parameter allows the operation of this feature to be enabled or disabled.
"Engine Fan Reversing Feature"
The "Engine Fan Reversing Feature" parameter allows the operation of this feature to be enabled or disabled.
"Engine Retarder Enable Command"
The "Engine Retarder Enable Command" parameter allows the operation of this feature to be enabled or disabled. If your application is equipped with a compression brake, this parameter should be programmed to "Enabled".
"Engine Security System Status"
This parameter allows the Machine Security System to be disabled or removed. If the Machine Security System is removed from the machine and this parameter is not programmed to "Disabled", the engine will not start. Factory passwords are required.
Parameter Table
Customer Specified Parameters     | |||
---|---|---|---|
Parameter     | Available Range or Options     | Default     | Required Password     |
"Product ID"     | 8 characters     | blank     | none     |
"Equipment ID"     | 17 characters     | blank     | none     |
"Engine Serial Number"     | 8 characters     | blank     | none     |
"FLS"     | -128 to +127     | 0     | Factory     |
"FTS"     | -128 to +127     | 0     | Factory     |
"Throttle Lock Engine Speed Limit"     | 850 to 3000     | 2250     | none     |
"Ether Control"     | "Enabled" or "Disabled"     | "Disabled"     | none     |
"System Battery Voltage Low Elevated Idle"     | "Enabled" or "Disabled"     | "Enabled"     | none     |
"Engine Fan Control" (1)     | "On" or "Off"     | "On"     | none     |
"Engine Fan Reversing Feature" (1)     | "Enabled" or "Disabled"     | "Disabled"     | none     |
"Engine Retarder Enable Command" (1)     | "Enabled" or "Disabled"     | "Disabled"     | none     |
"Engine Security System Status"     | "Enabled" or "Disabled"     | "Disabled"     | Factory     |
( 1 ) | This parameter is only available on certain applications. |
Parameter Worksheet
Record the following information before you change any programmable parameter.
Information from ECM     | |
---|---|
"Product ID"     |     |
"Equipment ID"     |     |
"Engine Serial Number"     |     |
"ECM Serial Number"     |     |
"Personality Module Part Number"     |     |
"Personality Module Release Date"     |     |
"Personality Module Description"     |     |
"FLS"     |     |
"FTS"     |     |
"Throttle Lock Engine Speed Limit"     |     |
"Ether Control"     |     |
"System Battery Voltage Low Elevated Idle"     |     |
"Engine Fan Control" (1)     |     |
"Engine Fan Reversing Feature" (1)     |     |
"Engine Retarder Enable Command" (1)     |     |
"Engine Security System Status"     |     |
"Total Tattletale"     |     |
Injector Trim Code (1)     |     |
Injector Trim Code (2)     |     |
Injector Trim Code (3)     |     |
Injector Trim Code (4)     |     |
Injector Trim Code (5)     |     |
Injector Trim Code (6)     |     |
Information From Engine Information Plate     | |
Engine Serial Number     |     |
Full Load Setting (for new ECM)     |
    |
Full Torque Setting (for new ECM)     |
    |
( 1 ) | This parameter is only available on certain applications. |
Note: Compare the FLS and the FTS from the ECM with the values that are listed on the Engine Information Plate. The FLS and the FTS should only be changed because of a mechanical change in the engine. The use of the wrong parameters could cause damage to the engine.