Hood - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 2     |
Start By:
- Prepare the machine for disassembly and assembly procedures. For additional information, refer to Disassembly and Assembly, "Preparation for Disassembly".
Note: Put identification on all lines, hoses, wires, and tubes for installation purposes. Use caps and plugs on all lines, hoses, and tubes in order to prevent fluid loss or contamination of the systems.
- Open the radiator grill.
Show/hide table
Illustration 1 | g00851713 |
- Remove bolt (1) and the washer from the hose clip on the refrigerant line.
Show/hide table
Illustration 2 | g00851740 |
- Remove three bolts (2), the washers, and refrigerant condenser (3) .
- Secure refrigerant condenser (3) to the oil cooler.
- Disconnect harness assemblies (3A) .
Show/hide table
Illustration 3 | g00949071 |
- Disconnect the harness assembly from connector (4) and backup alarm (5) .
Show/hide table
Illustration 4 | g00851770 |
- Disconnect harness assemblies (6) .
Show/hide table
Illustration 5 | g00851827 |
- Cut cable straps (7) .
- Remove bolts (13) .
Show/hide table
Illustration 6 | g00949073 |
Show/hide table
Illustration 7 | g00858154 |
- Remove cover (12), and disconnect the harness assembly for the toggle switch.
- Remove bolt (10) from actuator assembly (11) .
- Remove bolts (9) which hold the engine hood to the machine.
- Attach Tooling (A) and a suitable lifting device to engine hood (8) .
- Remove engine hood (8) from the machine. The weight of engine hood (8) is approximately 78 kg (170 lb).
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 2     |
- Attach Tooling (A) and a suitable lifting device to engine hood (8). The weight of engine hood (8) is approximately 78 kg (170 lb).
Show/hide table
Illustration 8 | g00949073 |
Show/hide table
Illustration 9 | g00858154 |
- Install engine hood (8) on the machine.
- Install bolts (9) .
- Install bolt (10) on actuator assembly (11) .
- Connect the harness assembly for the toggle switch. Install cover (12) and bolts (13) .
- Connect harness assemblies (6) .
Show/hide table
Illustration 10 | g00851827 |
- Install cable straps (7) .
- Connect the harness assemblies to connector (4) and backup alarm (5) .
Show/hide table
Illustration 11 | g00851770 |
- Connect harness assemblies (3A) .
Show/hide table
Illustration 12 | g00949071 |
- Install refrigerant condenser (3), three bolts (2), and the washers.
Show/hide table
Illustration 13 | g00851740 |
- Install the hose clip on the refrigerant line. Install bolt (1) and the washer.
- Close the radiator grill.
Show/hide table
Illustration 14 | g00851713 |
Caterpillar Information System:
14H Motor Grader Condenser (Refrigerant) - Clean
CB-634D Paving Compactor Engine Air Filter Service Indicator - Inspect
14H Motor Grader Circle Top - Lubricate
16H Motor Grader Circle Drive Pinion Teeth - Lubricate
CB-634D Paving Compactor Engine Air Filter Secondary Element - Replace
16H Motor Grader Circle Drive Oil Level - Check
CB-634D Paving Compactor Engine Air Filter Primary Element - Clean/Replace
570B Wheel Harvester and 580B Wheel Harvester Engine Supplement Muffler - Remove and Install
CB-634D Paving Compactor Eccentric Weight Housing Oil Level - Check
16H Motor Grader Circle Drive Oil - Change
16H Motor Grader Circle Clearances - Check/Adjust
570B Wheel Harvester and 580B Wheel Harvester Engine Supplement Air Cleaner - Remove and Install
16H Motor Grader Crankshaft Vibration Damper - Inspect
14H Motor Grader Drawbar Ball and Socket - Lubricate
533 and 543 Wheel Feller Bunchers Water Cleaning System (Pressurized) - Test
533 and 543 Wheel Feller Bunchers Water Cleaning System (Pressurized) - Purge
CB-634D Paving Compactor Engine Crankcase Breather - Clean
CB-634D Paving Compactor Engine Governor Oil Supply Screen - Clean/Inspect/Replace
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Rim Group
CP-433E, CS-423E and CS433E Vibratory Soil Compactors Machine Systems Padded Drum Scraper - Scraper on Shell Kit Attachment
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Axle (without Brakes) - Assemble
PM-465 Cold Planer Reference Material
CP-433E, CS-423E and CS433E Vibratory Soil Compactors Machine Systems Padded Drum Scraper - Flexible Scrapers
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Design