Piston Motor (Axle Propel) - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| ZZ | 6V-9511 | 端面密封螺塞 (1 3/16 - 12 螺纹) | 2 |
| 6V-9832 | 盖组件 (1 3/16 - 12 螺纹) | 2 | |
注: 维修数据：拆卸和安装中的工具 (ZZ) 将不在图示中列出。 显示这一工具是为了协助有经验的维修人员。
Show/hide table
 |
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后，液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前，如果不事先释放压力，可能会造成严重伤害。 卸下液压系统的部件或管路时，确保所有的作业机具都已降到地面上，而且液压油温度已冷。 只能在发动机停机，并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修机器时，务必小心，确保用容器盛接流出的油液。 在打开任何舱室或解体任何储有液体的部件之前，要准备好合适的容器收集液体。 有关可提供予卡特彼勒机器的工具及适合于盛装油液的容器，请参阅专门出版物, NENG2500, "卡特彼勒工具及车间用品指南"。 根据当地法规处置所有液体。 |
注: 为便于安装，在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将软管组件 (2) 从轮轴推进马达 (1) 上拆下。
Show/hide table
 | |
| 图 1 | g00837607 |
- 利用适当的起吊设备拆下轮轴推进马达 (1) 。 拆下螺栓 (3) ，然后从机器上拆下轮轴推进马达 (1) 。 轮轴推进马达的重量约为 24 kg (52 lb)。
Caterpillar Information System:
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0713 FMI 03 Rocker Switch (Auto Retarder On/Off) Voltage Above Normal - Test
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0712 FMI 06 Lamp (Retarder Indicator) Current Above Normal - Test
TH350B, TH355B, TH360B and TH460B Telehandlers Engine Air Filter Primary Element - Clean/Replace
TH350B, TH355B, TH360B and TH460B Telehandlers Drive Shaft Spline - Lubricate
2001/12/24 A New Housing for the Interaxle Differential Lock Improves the Capability of the Lock {1164, 3159}
735 Articulated Truck Power Train Hitch Drive Shaft Bearings - Install
TH350B, TH355B, TH360B and TH460B Telehandlers Boom Telescoping Cylinder Air - Purge
TH350B, TH355B, TH360B and TH460B Telehandlers Boom Pivot Shaft - Lubricate
725 and 730 Articulated Trucks Braking System Operational Checks
988G Wheel Loader STIC Transmission Control
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Electronic Control Module (Hydrostatic Transmission)
PM-465 Cold Planer Rotor Cutter Bits - Inspect/Replace
773E Off-Highway Truck and 775E Off-Highway Truck Air System and Brakes Brake Hydraulic System
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Piston Motor (Axle Propel) - Install
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System General Information
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0713 FMI 04 Rocker Switch (Auto Retarder On/Off) Voltage Below Normal - Test
768C, 769C, 769D, 772B, 773B, 773D, 776C, 777B, 777D, 784B, 785, 785B, 789, 789B, 793, 793B and 793C Off-Highway Truck/Tractors and 771C, 771D and 775D Quarry Trucks Automatic Retarder Control (ARC) System CID 0714 FMI 03 Pressure Switch (Auto Retarder) Voltage Above Normal - Test
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Padded Drum Scraper - Remove and Install
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks ECM/Personality Module
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader System Configuration Parameters
CP-433E, CS-423E and CS-433E Paving Compactors Belts - Inspect/Adjust/Replace
2001/10/29 The Service Interval for Tightening Sprocket Retaining Nuts {4164}
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Control Valve (Shift) - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks Electrical Power Supply