Hood Tilt Actuator - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 1     |
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Note: Put identification marks on all electrical connectors for installation purposes.
- Open the engine hood. The hood actuator is located on the right side of the machine.
- Remove plug (1) from the center of the engine hood.
Show/hide table
Illustration 1 | g00363774 |
- Install Tooling (A) in place of plug (1). Attach a suitable lifting sling to Tooling (A) in order to support the hood.
Show/hide table
Illustration 2 | g00363776 |
- Remove five bolts (2) and the washers. Remove cover (3) .
Show/hide table
Illustration 3 | g00836751 |
- Cut wire tie (4) .
Show/hide table
Illustration 4 | g00836753 |
- Disconnect electrical connector (5) .
- Remove nine bolts (6) and the washers.
Show/hide table
Illustration 5 | g00836756 |
- Remove step (7) .
- Remove pin (8) and the cotter pin which is not shown.
Show/hide table
Illustration 6 | g00836757 |
- Remove screws (9) and remove cover (10) .
Show/hide table
Illustration 7 | g00836758 |
- Remove bolt (11) and the washer.
Show/hide table
Illustration 8 | g00836762 |
- Remove hinge assembly (12) .
- Disconnect hood tilt actuator (13) from the hood.
- Remove hood actuator (14) .
Show/hide table
Illustration 9 | g00836764 |
Caterpillar Information System:
773E Off-Highway Truck Fuel System Water Separator - Drain
966G Series II and 972G Series II Wheel Loaders Engine Supplement Hood Tilt Actuator - Install
773D Off-Highway Truck and 775D Quarry Truck Towing With Inoperable Engine
773E and 775E Off-Highway Truck Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
793C and 793C XQ Off-Highway Truck Steering System Center Arm (Steering) - Adjust
773E Off-Highway Truck Engine Starting with Auxiliary Start Receptacle
773E and 775E Off-Highway Truck Specifications (Power Train)
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Lift Cylinder
773E Off-Highway Truck Power Train Specifications (Power Train)
MT735, MT745, MT755 and MT765 Agricultural Tractors Engine Supplement Alternator - Remove and Install
988G Wheel Loader Electrohydraulic System MID 082 - CID 0562 - FMI 09
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Piston Pump (Vibratory) - Assemble
TH560B Telehandler Transmission and Hydraulic System Oil Filter - Replace
IT62G Series II Integrated Toolcarrier Ground Speed Limiter - If Equipped
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Hydraulic Tank - Remove and Install
TH560B Telehandler Transmission and Hydraulic System Oil Level - Check
TH210 and TH215 Telehandlers Steering System Operational Checks
735 Articulated Truck Power Train Hitch Drive Shaft Bearings - Remove
735 Articulated Truck Power Train Hitch Drive Shaft - Remove and Install
773E Off-Highway Truck Oil Filter (Steering) - Replace
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Bank Valve (Backhoe) (Pilot Operated)
TH210 and TH215 Telehandlers Steering System Steering System Troubleshooting
769D Off-Highway Truck and 771D Quarry Truck Oil Filter (Steering Pump Case Drain) - Replace
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Diagnostic Code List