IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System Caterpillar


MID 081 - CID 0644 - FMI 05

Usage:

IT28F 1JL
Conditions Which Generate This Code:


Illustration 1g00618544

Locations of the Solenoid

(1) Solenoid 1

(2) Solenoid 2

(3) Solenoid 3

(4) Solenoid 4

(5) Solenoid 5

(6) Solenoid 6




Illustration 2g00619047

Schematic of Solenoid 4

Use table 1 in order to determine the solenoids that are energized. Table 1 identifies the solenoids that are energized for each position on the shift lever.

Table 1
Gear     Solenoid that is Energized    
Neutral     No solenoids are energized.    
Forward 1     3 and 4    
Forward 2     1 and 4    
Forward 3     3 and 5    
Forward 4     1 and 5    
Forward 5     1 and 6    
Reverse 1     2 and 4    
Reverse 2     2 and 5    
Reverse 3     2 and 6    

Note: The approximate coil resistance of the solenoid is 34 ohms at 25 °C (77.0 °F).

This diagnostic code is recorded when the ECM reads the voltage of the solenoid circuit as being below normal range (open circuit).

Note: This procedure can cause new diagnostic codes to be recorded. Ignore these created diagnostic codes. Complete the following procedure. Then clear the created diagnostic codes.

This diagnostic code is associated with transmission solenoid 4.

FMI 05 is recorded when the transmission electronic control module senses an incomplete circuit. The circuit of the solenoid is incomplete.

Test Step 1. CHECK THE HARNESS FOR AN OPEN.

  1. Turn the key start switch to the OFF position.

  1. Disconnect the machine harness from the control module.

  1. Measure the resistance between contact 39 and contact 34.

Expected Result:

The resistance is between 7 ohms and 10 ohms.

Results:

  • YES - The resistance is between 7 ohms and 10 ohms. The sensor is operating properly. Inspect the harness connector and inspect the contacts. Verify that the diagnostic code is present. If the code is present, the transmission electronic control module has failed.

    Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Also, recheck if the diagnostic code is active. If the cause of the diagnostic code is not found, replace the transmission ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". Clear the diagnostic code. Refer to Systems Operation, "Diagnostic Operation".

    Stop.

  • NO - The resistance is not between 7 ohms and 10 ohms. The machine harness has failed or the solenoid has failed.

    Repair: Repair the harness or replace the harness and/or the solenoid. Clear the diagnostic code. Refer to Systems Operation, "Diagnostic Operation".

    Stop.

Caterpillar Information System:

AS2301 Screed Burner Group (Extender) - Install
TK711 Track Feller Buncher, TK721 Track Feller Buncher, TK722 Track Feller Buncher and TK732 Track Feller Buncher Machine Systems Travel Motor Head
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0644 - FMI 03
Product Identification Numbers (PIN) Location Guide Bulldozer
AS2301 Screed Burner Group (Extender) - Remove
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0643 - FMI 06
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0643 - FMI 05
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0643 - FMI 03
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Hydraulic System Oil Level - Check
CP-323C and CS-323C Paving Compactors Rollover Protective Structure (ROPS) - Inspect
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0642 - FMI 06
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0642 - FMI 05
TK1051 Track Feller Buncher Swing Gear - Lubricate
Product Identification Numbers (PIN) Location Guide Ripper
Air Conditioning and Heating R134a for All Caterpillar Machines Electronic Heat Control - Test
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0644 - FMI 06
AS2301 Screed Burner Group (Main) - Remove
2001/05/14 A New Support Is Used on the Boom and Stick of the Knuckle Boom Loaders {5057, 5057, 6501, 6502}
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0645 - FMI 03
TK1051 Track Feller Buncher Machine Systems Pilot Valve (Travel and Steering)
IT12F, IT14F, IT18F, IT24F and IT28F Integrated Toolcarriers and 910F, 918F, 924F and 928F Wheel Loaders Power Train Electronic Control System MID 081 - CID 0645 - FMI 05
2001/05/14 Special Instruction, REHS0142-05 for Backhoe Loader Pin Bores is Now Updated {6104, 6119, 6501, 6502, 6503, 6506, 7054}
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Centershift Lock
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Cooling System Coolant Level - Check
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.