Window Wiper and Wiper Motor (Rear) - Install
Removal Procedure
Show/hide table
| NOTICE |
|---|
Do not operate the wiper motor before the wiper arm assembly is installed. A new wiper motor is preset in the parked position. If the wiper motor is operated before installation of the wiper arm assembly, misalignment will occur. This can cause damage to the wiper motor, the wiper arm assembly, and/or the window. Do not manually rotate the wiper arm assembly on the shaft. |
Note: The rear window must be in the DOWN position.
- Install window wiper motor (21) in position.
Show/hide table
 | |
| Illustration 1 | g00758710 |
- Install two spacers (18) in position. Spacers (18) are inside the cab.
Show/hide table
 | |
| Illustration 2 | g00758719 |
- Install two screws and the washers (17). Tighten screws (17) to a torque of 6 ± 1 N·m (4 ± 0.7 lb ft). Screws and the washers will secure the window wiper motor.
Show/hide table
 | |
| Illustration 3 | g00758667 |
- Connect electrical connector (20) .
Show/hide table
 | |
| Illustration 4 | g00758687 |
- Install wire tie-wrap (19). Wire tie-wrap (19) will secure electrical connector (20) .
Show/hide table
 | |
| Illustration 5 | g00758682 |
- Install the headliner in position. Install two plastic retainers (11). Install two plastic retainers to the opposite side of the headliner. The plastic retainers will secure a portion of the headliner.
Show/hide table
 | |
| Illustration 6 | g00757348 |
- Connect two wires (10) to light (9) .
Show/hide table
 | |
| Illustration 7 | g00757347 |
- Install light (9) into the headliner.
Show/hide table
 | |
| Illustration 8 | g00757344 |
- Install face plate opening (8) in position. Secure face plate opening (8) with four screws (7) .
Show/hide table
 | |
| Illustration 9 | g00757330 |
- Install speaker cover (6) in position. Secure speaker cover (6) with four screws (5) .
Show/hide table
 | |
| Illustration 10 | g00757274 |
- Install the speaker cover on the opposite side.
- Install two washers and one nut (16) on the shaft of the window wiper motor.
Show/hide table
 | |
| Illustration 11 | g00758642 |
- Apply 4C-4030 Thread Lock Compound to the threads of the window wiper motor.
- Install window wiper (14). Install the window wiper at the top of the rear window.
Show/hide table
 | |
| Illustration 12 | g00759298 |
- Install the washer and nut (12). Torque nut (12) to 24 ± 1 N·m (17 ± 1 lb ft).
Show/hide table
 | |
| Illustration 13 | g00758602 |
- Close cap (13) over nut (12) .
- Install tube (15) of the washer fluid bottle on window wiper blade (14) .
Show/hide table
 | |
| Illustration 14 | g00758609 |
- Connect the hose of the washer fluid bottle to the fitting. Install the hose to dimension (A). Dimension (A) is 1.0 mm (0.04 inch).
Note: Do not use petroleum lubricants on the hose ends. Do not stretch the hose between connections.
Show/hide table
 | |
| Illustration 15 | g00488225 |
- Install mirror (1). Secure the mirror with washer (4) and nut (3) .
Show/hide table
 | |
| Illustration 16 | g00756736 |
- Install cap (2) on mirror (1) .
Show/hide table
 | |
| Illustration 17 | g00756730 |
- Move the start switch to the ON position.
- Move the switch of the rear window wiper to the ON position. Check the movement of the wiper blade and the motor operation.
Caterpillar Information System:
TK1051 Track Feller Buncher Air Conditioning and Heating Control
3176C and 3196 Engines for Caterpillar Built Machines E015 High Engine Coolant Temperature Derate
HP750 Processing Head General Hazard Information
RM-250C Reclaimer Mixer Engine Oil Sample - Obtain
2000/11/27 Correction to Parts Manual {7524}
3176C Engine for Caterpillar Built Machines E600 High Hydraulic Oil Temperature Warning
2000/11/27 Correction to the "Service Sheet" {7524}
RM-250C Reclaimer Mixer Rotor Chain Drive Case Oil Level - Check
Water Spray System Piston Pump (Water Spray)
2000/11/27 A Seal Kit is now Available for Servicing the Axle Oil Cooling Pump {5073}
Water Spray System Gear Motor (Water Spray)
C-15 and C-16 Industrial Engines Engine Design
3176C and 3196 Engines for Caterpillar Built Machines E025 High Inlet Air Temperature Derate
2000/11/27 Revision to the "Service Sheet" for the 250 Hour Service {7524}
3456 Engine, 836G Landfill Compactor, 834G Wheel Dozer and 988G Wheel Loader Service Brake Pedal Switch Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines E096 High Fuel Pressure
C7 and C9 Engines for Caterpillar Built Machines CID 0091 FMI 02 Incorrect Throttle Switch inputs
797 Off-Highway Truck Power Train Pressure Sensor (Differential Oil)
797 Off-Highway Truck Power Train Bypass Switch (Differential Oil Filter)
2001/01/15 Improved Mounting Pins and Bushings Are Now Used On The Equalizer Bar {7206}
725 and 730 Articulated Trucks Braking System Pressure for Piston Pump (Brake) - Test
797 Off-Highway Truck Power Train Bypass Switch (Final Drive Filter)
3176C Engine for Caterpillar Built Machines CID 0545 FMI 05 Ether Start Relay open/short to +batt
797 Off-Highway Truck Power Train Pressure Switch (Final Drive Oil)