Electric Drive Pump (Secondary Steering and Brake Release) - Remove
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 138-7575 | 连杆支架 | 1 |
Show/hide table
 |
|
热油和热的部件可能会导致人员受伤。 请勿让热的液压油或热的零部件与皮肤接触。 |
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 |
注: 将盖和塞安装在全部孔口上，以免污垢或碎屑进入系统。 清洁度是一项重要的因素。 拆卸步骤开始之前，应彻底清洁部件外部。 这将防止脏污进入内部机构。
- 将适当的容器放置在电动泵下方收集液压油，以便于存放或处理。
- 将转向油箱中的液压油排入合适的容器中，以便存放或进行处置。 转向油箱的容量为
40 L (11 US gal) 。 请参阅操作和保养手册, "转向系统油 – 更换"。Show/hide table
图 1 g00697541 - 将工具 (A) 固定至板 (3)。 将适当的吊索固定到工具 (A) 上。 将吊索固定到适当的举倾机构上。
- 拆下螺栓 (1) 和垫圈。 拆下四个螺栓 (2) 和垫圈。 拆下板 (3)。
Show/hide table
图 2 g00697543 - 从电动泵 (4) 上断开电缆组件 (5) 和电缆组件 (6)。
Show/hide table
图 3 g00697544 - 从电动泵上断开软管组件 (7)、软管组件 (8) 和软管组件 (11)。
- 从电动泵上断开软管组件 (9)、软管组件 (10) 和软管组件 (12)。
Show/hide table
图 4 g00697545 - 将适当的吊索绕电动泵 (4) 放置，如图所示。 将适当的起吊设备固定在举倾机构上。 拆下将电动泵 (4) 固定到机器上的四个螺母 (13) 和硬垫圈。
- 从机器上拆下电动泵 (4)。 电动泵的重量为
26 kg (57 lb) 。
Caterpillar Information System:
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Drum Propel) - Test
2014/02/20 Correction to Service Magazine, SEPD0533 , "A New Inlet Valve is Released for use in 3116 and in 3126 Machine Engines with Two Valve Configuration" {1105}
3114, 3116, and 3126 Engines Basic Engine
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Signal and Pressure Reducing Valve (Steering)
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Signal and Pressure Reducing Valve (Steering)
D400E Series II Articulated Truck Steering, Suspension, and Ejector Body Hydraulic Systems Secondary Steering Pump and Electric Motor
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Slack Adjuster (Rear) - Install
TH62, TH63, TH82, TH83 and TH103 Telehandlers Longitudinal Stability Indicator System Calibration
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Slack Adjuster (Rear) - Remove
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Service and Parking Brake (Rear) - Assemble
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Axle Propel) - Test
CS-531D, CP-533D and CS-533D Vibratory Compactors Windows - Clean - If Equipped
C-10, C-12, C-15 and C-16 Industrial Engines CID 0320 FMI 02 Speed/Timing Sensor Loss of Signal
216, 226 and 228 Skid Steer Loaders Powertrain Piston Motor (Hydrostatic) - Remove and Install
776D, 777D and 777D HAA Off-Highway Trucks Machine Systems Electric Drive Pump (Secondary Steering and Brake Release) - Install
D400E Series II Ejector Truck Steering, Suspension, and Ejector Body Hydraulic Systems Ejector Cylinder
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Oil Pump - Inspect
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options General Information (SR4B for 3500 Engines)
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Generator Wiring Diagrams (SR4B for 3500 Engines)
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Main Stator and Voltage Sensing Lead Connections (All Except SR4B for 3500 Engines)
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders Event Codes
2000/05/22 New Seal Retainers and a New Plate Are Used with Duo-Cone Seals in Order to Increase Performance {4251, 4267, 7561}
CS-431C, CP-433C and CS-433C Vibratory Compactors Propel System Thermal Bypass Valve - Test
3508B Engine for 854G Wheel Dozers and 992G Wheel Loaders E017 High Engine Coolant Temperature Warning