Camshaft - Install
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil.
- Carefully install camshaft (10) and camshaft gear (4) in cylinder block (11). Be careful not to damage the lobes of the camshaft or the camshaft bearings.
Show/hide table
 | |
| Illustration 1 | g01003212 |
- Align the bolt holes in camshaft retainer (9) with the bolt holes in cylinder block (11). Rotate camshaft gear (4) in order to align access hole (8) in the camshaft gear with the hole for bolt (6). Install bolt (6) and bolt (7) that secures camshaft retainer (9) in position on cylinder block (11). Tighten bolt (6) and bolt (7) to a torque of 11 N·m (95 lb in).
Show/hide table
 | |
| Illustration 2 | g00828468 |
- Install idler gear (5). Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Note: When you install the idler gear, ensure that timing marks (2) are aligned on the following components.
- Camshaft gear (4)
- Idler gear (5)
- Crankshaft gear (3)
- Camshaft gear (4)
Show/hide table
 | |
| Illustration 3 | g00828467 |
- Install slider (1) to camshaft gear (4) .
End By:
- Install the engine front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump - Install".
- Install the fuel injection pump. Refer to Disassembly and assembly, "Fuel Injection Pump - Install".
- Install the lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
Caterpillar Information System:
216, 226 and 228 Skid Steer Loaders Machine Systems Quick Coupler
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Camshaft - Remove
CB-214D, CB-224D and CB-225D Vibratory Compactors Vibratory System Eccentric Weight Housing
824G Wheel Tractor, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System General Information
784C and 785C Off-Highway Truck/Tractors Window Washer Bottle - Fill
3408E and 3412E Engines for Caterpillar Built Machines Low Power/Poor or No Response to Throttle
572R Pipelayer Machine Systems Combination Valve (Boom) - Assemble
572R Pipelayer Machine Systems Combination Valve (Boom) - Disassemble
2000/01/17 New Engine Software Reduces "High Boost" Events {1901, 1917, 7620}
3114, 3116 and 3126 MUI Engine Governors Throttle Lever Orientation (Types IV, V, VI, VII, and Some III) - Check
2000/01/17 A New Cup Holder is Available {7300}
2000/04/03 Correction for Specifications of the Backhoe Linkage {5109, 5112, 6506}
784C and 785C Off-Highway Truck/Tractors Engine Air Filter Service Indicator Screen - Clean/Replace
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
CB-214D, CB-224D and CB-225D Vibratory Compactors Vibratory System Gear Motor (Vibratory)
793C Off-Highway Truck Window Washer Bottle - Fill
CB-214D, CB-224D and CB-225D Vibratory Compactors Vibratory System Machine Preparation for Troubleshooting
CB-214D, CB-224D and CB-225D Vibratory Compactors Vibratory System Visual Inspection
CB-214D, CB-224D and CB-225D Vibratory Compactors Vibratory System Vibratory System Troubleshooting
CB-214D, CB-224D and CB-225D Vibratory Compactors Vibratory System Vibratory Frequency - Test and Adjust
CB-214D, CB-224D and CB-225D Vibratory Compactors Vibratory System Eccentric Weight
1999/12/06 The VIMSpc99 Software May Experience A Problem When Generating Reports {7601}
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Crankshaft - Remove
D350E Series II Articulated Truck Metering Pump (Steering) - Disassemble