Control Valve (Boom Stop) - Install
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Connect hydraulic line (5) to control valve (6) .
Show/hide table
Illustration 1 | g00634943 |
- Position the control valve in place. Install three bolts (4), six washers, and three nuts.
Show/hide table
Illustration 2 | g00634926 |
- Connect two hydraulic lines (3) .
Show/hide table
Illustration 3 | g00634890 |
- Install plate (1) and four bolts (2) .
Show/hide table
Illustration 4 | g00634888 |
- Fill the hydraulic tank. Refer to Operation and Maintenance Manual, SEBU7160, "Hydraulic System Oil - Change" for the correct procedure.
Caterpillar Information System:
C-9 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Neutral Start Function
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0526 - FMI 05 Turbo Wastegate Drive current low
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Electronic Control Module (ECM) - Replace
CS-531D, CP-533D and CS-533D Vibratory Compactors Tire Inflation - Check
527 Track-Type Skidder Machine Supplements Bulldozer Lift Cylinder - Assemble
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Directional Shift Management Function
C9 Engine For Caterpillar Built Machines Lifter Group - Remove and Install
3524B Engines for Off-Highway Trucks MID 036 - CID 0296 - FMI 09 Unable to communicate with Transmission ECM
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 06 Engine Cooling Fan Solenoid short to ground
12H, 140H and 160H Motor Graders Machine Systems Blade Lift - Remove
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0291 - FMI 05 Engine Cooling Fan Solenoid open circuit
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 0526 - FMI 06 Turbo Wastegate Drive current high
561M Pipelayer Boom Kickout Mechanism - Remove and Install
784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks Power Train Electronic Control System Elevated Downshift Function
CS-531D, CP-533D and CS-533D Vibratory Compactors Tilt Hood Actuator - Lubricate
12H, 140H and 160H Motor Graders Machine Systems Blade Lift - Install
D350E Series II and D400E Series II Articulated Trucks Cooling System Pressure Cap - Clean/Replace
12H, 140H and 160H Motor Graders Machine Systems Centershift Cylinder - Remove
527 Track-Type Skidder Machine Supplements Bulldozer Tilt Cylinder - Remove
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Air System and Brakes Bearing Preload for Service Brake - Adjust
12H, 140H and 160H Motor Graders Machine Systems Centershift Cylinder - Install
12H, 140H and 160H Motor Graders Machine Systems Centershift Lock - Disassemble
12H, 140H and 160H Motor Graders Machine Systems Centershift Lock - Remove