Engine Oil Scavenge Pump
Show/hide table
| |
| 图 1 | g03836640 |
|
仰视图 | |
Show/hide table
| |
| 图 2 | g03836639 |
|
剖面 A-A | |
Show/hide table
| 注意 |
|---|
|
操作之前，必须使用干净的发动机机油润滑泵体，并且泵必须能灵活运转，否则就会导致部件的损坏。 |
Show/hide table
| |
| 图 3 | g03836638 |
Show/hide table
| 技术规格 - 1W-8508 扫油泵 | |||
|---|---|---|---|
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 4 | 3H-2750 螺栓 | 拧紧至扭矩为 |
| 2 | 2 | - | 装配前，用清洁的发动机机油稍微润滑 O 形密封圈的孔。 |
| B | 1 | 1W-8515 齿轮 | 长度为 扫油泵体中新齿轮孔的深度为 |
| C | 1 | 161-2510 驱动轴 | 直径为 装配后，新驱动轴的 1W-6005 衬套孔径为 |
| D | 1 | 1W-8509 扫油泵体 | 扫油泵体上的 1W-6005 衬套安装深度为 |
| E | 1 | 1W-8511 惰轮轴组件 | 自惰轮轴组件末端至齿轮端面的距离为 |
| F | 1 | 106-9865 惰轮轴 | 直径为 1W-6005 衬套上的新惰轮轴孔径为 |
| 3 | 1 | 0S-0484 螺栓 | 采用下述步骤拧紧螺栓：
将驱动齿轮安装到驱动轴组件前，清洁轴和齿轮孔。 1. 敲打驱动齿轮以座合驱动齿轮的锥形部分。 2. 拧紧螺栓至扭矩 3. 重复此步骤直到扭矩不再变化。 |
| G | - | - | 从中线穿过轴承孔的衬套接头位置为 45 ± 15 度。 |
| H | 2 | 1W-6005 衬套 | 7N-8527 泵盖上的安装深度为 |
| J | 2 | 4M-3248 空心定位销 | 空心定位销的延伸量为 |
Caterpillar Information System:
797 and 797B Off-Highway Truck Glossary of Electrical Terms
D350E Series II and D400E Series II Articulated Trucks 3406E Engine Supplement Radiator - Disassemble
784C and 785C Off-Highway Truck Power Train Final Drive - Remove
773D and 775D Quarry Trucks and 773E and 775E Off-Highway Trucks Power Train Spindle - Remove
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Bucket Cutting Edges - Inspect/Replace
3512B and 3516B Engine Supplement for and 784C,, 785C and and 785C HAA Off-Highway Truck/Tractors Engine Oil Filter Bypass Valve - Remove and Install
517 Track-Type Skidder Engine Supplement Fan Drive - Remove
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Tandem Gear Pump (Charge) - Assemble
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Level Gauge (Dipstick) - Remove and Install
517 Track-Type Skidder Engine Supplement Fan - Install
834G Wheel Tractor and 836G Landfill Compactor Steering System Steering Control Valve
784C and 785C Off-Highway Truck Power Train Axle Shaft - Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Machine Systems Implement Pump - Disassemble
773D and 775D Quarry Trucks and 773E and 775E Off-Highway Trucks Power Train Spindle - Install
D400E Series II Articulated Truck Hoist, Steering, and Brake System Tank - Install
773D and 775D Quarry Trucks and 773E and 775E Off-Highway Trucks Power Train Differential and Bevel Gear - Remove
539 Knuckleboom Loader Hydraulic System Swing Motor
561M Pipelayer Hydraulic System Counterweight Cylinder
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Engine Trunnion - Install
143H and 163H Motor Graders All Wheel Drive All Wheel Drive Electronic Control - Test
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Screen (Hoist and Rear Brake Oil Cooler) - Remove and Install
3054 Engine for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Type 1 Engines and 9RM Engines
D400E Series II Articulated Truck Power Train Differential and Bevel Gear (Front and Rear) - Assemble
539 Knuckleboom Loader Hydraulic System Swing Drive