Fuel Transfer Pump - Assemble
组装步骤
Show/hide table
| 注意 |
|---|
机器做检查、保养、测试、调整和修理时，必须小心，不让油液流出。 在打开任何舱室或解体任何储有液体的零件之前，要准备好合适的容器收集流出液体。 有关可提供予卡特彼勒机器的工具及适合于盛装油液的容器，请参阅专门出版物, NENG2500, "卡特彼勒工具及车间用品指南"。 按照本地法规和指令处置所有液体。 |
- 将阀门组件 (18) 安装到壳体 (3) 中。
Show/hide table
 | |
| 图 1 | g00498470 |
- 将清洁的柴油涂覆在密封件 (16) 上。 将密封件 (16) 安装到盖 (17) 上，如图所示。 安装两根螺栓，将盖 (17) 固定到壳体 (3) 上。
Show/hide table
 | |
| 图 2 | g00498687 |
- 将清洁的柴油涂覆在密封件 (8) 上。 将密封圈 (8) 安装到导管和挺杆组件 (9) 上。 将导管和挺杆组件 (9) 安装到壳体 (3) 中。
Show/hide table
 | |
| 图 3 | g00498334 |
Show/hide table
| 注意 |
|---|
挺杆和导管组件必须作为一个整体。 |
- 将清洁的柴油涂覆在 O 形密封圈 (11) 上。 将 O 形密封圈 (11) 在衬套 (10) 上放置到位。 将衬套 (10) 安装到壳体 (3) 中。
- 将活塞 (12) 安装到衬套 (10) 中。
- 将清洁的柴油涂覆在密封件 (13) 上。 将密封件 (13) 、阀门组件 (14) 和垫圈 (15) 在活塞 (12) 上放置到位。
- 将清洁的柴油涂覆在 O 形密封圈 (5) 和 (6) 上。 将 O 形密封圈 (5) 和 (6) 安装到盖 (1) 中。 将阀门组件 (7) 安装盖 (1) 中。
Show/hide table
 | |
| 图 4 | g00498980 |
- 将弹簧 (4) 安装到壳体 (3) 中。
Show/hide table
 | |
| 图 5 | g00499040 |
- 将盖 (1) 在壳体上放置到位，然后安装将盖固定到位的螺栓 (2) 。
Show/hide table
 | |
| 图 6 | g00498289 |
End By: 安装燃油输油泵。 请参考 解体与组装, "燃油输油泵 - 安装"。
Caterpillar Information System:
3304B and 3306B Engines for Caterpillar Built Machines Fuel Transfer Pump - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
784C and 785C Off-Highway Trucks Machine Systems Metering Pump (Steering) - Assemble
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0737 FMI 04 Position Sensor (Neutralizer Pedal) Voltage Below Normal - Test
D250E Series II and D300E Series II Articulated Trucks Machine Systems Hoist Cylinder - Install
980G Wheel Loader Power Train Output Transfer Gears to Transmission, Torque Converter - Connect
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0615 FMI 04 Position Sensor (Articulation) Voltage Below Normal - Test
D250E Series II and D300E Series II Articulated Trucks Power Train Final Drive - Assemble
554 Forwarder and 574 Forwarder Steering Control
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Cowling (Radiator) - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Hydraulic Displacement Control Valve Test
3406C Engines for Caterpillar Built Machines Crankshaft
784C and 785C Off-Highway Truck/Tractors Capacities (Refill)
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Hoist Cylinder
3176C and 3196 Industrial Engines Inlet Manifold - Remove
3406E On-Highway Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0738 FMI 04 Position Sensor (Ripper) Voltage Below Normal - Test
554 Forwarder and 574 Forwarder Engine Speed Control
3176C and 3196 Industrial Engines Inlet Manifold - Install
3406E On-Highway Engine Engine Oil Filter Base - Disassemble
824G , 825G and 826G Landfill Compactor Soil Compacting
3304B and 3306B Engines for Caterpillar Built Machines Water Pump - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Gear Pump (Steering and Brake Circuit)
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Metering Pump (Steering)