Traction Control Valve - Install
Installation Procedure
Show/hide table
 |
The space between the body and the frame becomes a zero clearance area when the body is lowered. Failure to install the retaining cable can result in injury or death to personnel working in this area. |
 |
- Install traction control (14). Install one clip (10), the three washers, and three bolts (9) .
Note: Inspect the O-ring seals for wear or for damage. If necessary, replace the O-ring seals.
Note: Lubricate the O-ring seals with the fluid that is being sealed.
Show/hide table
 | |
| Illustration 1 | g00475068 |
Show/hide table
 | |
| Illustration 2 | g00475070 |
- Connect the harness connection (15). Install harness connection (15) of the solenoid valve in the clip.
- Connect the harness connection (13). Install the harness connection (13) of the solenoid valve in the clip.
- Install connector (12) and tube (11) .
- Install fitting assemblies (3), (4), (5), and (6) .
- Connect hose assemblies (1), (2), (7), and (8) .
- Fill the hydraulic tank with oil to the correct level. Refer to Operation and Maintenance Manual.
End By: Disconnect the retaining cable. Refer to Disassembly and Assembly, "Truck Body Retaining Cable - Remove and Install" for the correct procedure.
Caterpillar Information System:
Caterpillar<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> AP-900B and Barber-Greene<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> BG-240C Asphalt Pavers Mounting and Dismounting
Electronic Modular Control Panel II (EMCP II) For MUI Engines Fault Log Viewing OP1
AP-1000B and BG-260C Asphalt Pavers Parking
Electronic Modular Control Panel II (EMCP II) For MUI Engines Service Mode
Electronic Modular Control Panel II (EMCP II) For MUI Engines Shutdown Mode
G3B, K3A and L3A Denso Alternators Component - Test
Electronic Modular Control Panel II (EMCP II) For MUI Engines Alarm Mode
572R Pipelayer Hydraulic System Load Sense Manifold
IT14G Integrated Toolcarrier Caterpillar Reference Material
IT14G Integrated Toolcarrier Single Lever Control
IT14G Integrated Toolcarrier Windows - Clean
IT14G Integrated Toolcarrier Walk-Around Inspection
Electronic Modular Control Panel II (EMCP II) For MUI Engines Engine/Generator Setpoint Viewing OP2
IT14G Integrated Toolcarrier Attachment Coupler Operation
Electronic Modular Control Panel II (EMCP II) For MUI Engines Password Entry OP3
793C Off-Highway Truck Machine Systems Hoist Cylinder - Remove and Install
Electronic Modular Control Panel II (EMCP II) For MUI Engines Fault Log Clearing OP4
793B Off-Highway Truck Air System and Brakes Gear Pump (Hoist and Rear Brake Cooling)
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Control Valve - Priority Flow
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Quick-Coupler Valve
Procedure to Install the 135-7462 Steering Control Valve {4307} Procedure to Install the 135-7462 Steering Control Valve {4307}
69D and 769D Off-Highway Trucks and 771D Quarry Truck Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
793B Off-Highway Truck Hydraulic System Relief Valve (Brake Oil Cooler)
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Machine Preparation for Troubleshooting