Parking Brake Release Oil Filter - Replace
Show/hide table
 | |
| Illustration 1 | g00405020 |
Show/hide table
 | |
| Illustration 2 | g00407938 |
- Remove the drain plug from the bottom of the filter housing. Drain the oil into a suitable container. Clean the drain plug and install the drain plug.
Note: Removing the drain plug from the bottom of the filter housing may not drain all of the oil from the filter.
Show/hide table
 |
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Remove the filter housing and the filter element. Discard the used filter element.
- Wash the filter housing in clean, nonflammable solvent.
- Inspect the seal in the housing base. If the seal is damaged, replace the seal with a new seal.
- Install the new element in the filter housing.
- Install the filter housing.
- Start the engine and operate at low idle. Check for leaks and make any necessary repairs.
- Observe the oil level. The transmission must be in the NEUTRAL position and the parking brake must be engaged.
- Maintain the oil level to the FULL mark in the sight gauge.
Show/hide table
 | |
| Illustration 3 | g00441963 |
- If necessary, add oil.
Caterpillar Information System:
784B and 785B Off-Highway Truck/Tractors Parking Brake Release Oil Filter - Replace
572R Pipelayer Final Drive
517 Track-Type Skidder Hydraulic System Oil Level - Check
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train CID 0368 FMI 04 Rotary Switch (Transmission Auto/Man) Voltage Below Normal - Test - Conventional Steering-Without Integrated Braking System
789B Off-Highway Truck Power Train Gear Pump (Torque Converter, Parking Brake Release, and Brake Cooling)
CP-563C and CS-563C Vibratory Compactors Stopping the Engine if an Electrical Malfunction Occurs
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Main Control Valve and Mounting Plate - Install
CP-563C and CS-563C Vibratory Compactors Stopping the Engine
517 Track-Type Skidder Transmission Oil Level - Check
572R Pipelayer Relief Valve (Torque Converter Outlet)
517 Track-Type Skidder Engine Oil Level - Check
527 Track-Type Skidder Seat Belt - Inspect
793B Off-Highway Truck Differential and Final Drive Oil - Inspect
784B and 785B Off-Highway Truck/Tractors Steering Accumulator - Check
789C Off-Highway Truck Power Train Torque Converter Inlet and Outlet Relief Valves
416C, 426C, 428C, 436C and 438C Backhoe Loaders Axles, Differential and Brakes Brake System Air - Purge
CP-563C and CS-563C Vibratory Compactors Equipment Lowering with Engine Stopped
CP-563C and CS-563C Vibratory Compactors Leaving the Machine
550, 570 and 580 Wheel Harvesters Pendulum Arm Bearings - Lubricate
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Minimizing Soil Disturbance
527 Track-Type Skidder Cooling System Level - Check
CP-563C and CS-563C Vibratory Compactors Shipping the Machine
550, 570 and 580 Wheel Harvesters Pendulum Arm Cylinder Bearings - Lubricate
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Flow Switch